Search results

  1. Prickster

    Nobody can figure it out prop loosing itself

    Yes sir, that is correct. Everytime it was out of the water. He is changing the entire motor set up. Going from a small pin Kawi 750 with TL, to a Yami BB with a charging system.
  2. Prickster

    Nobody can figure it out prop loosing itself

    ThatTowerGuy has a limp wrist, so that's his issue. LOL. But honestly, I have seen it happen once on his ski after being pulled from the inlet. Ski fired up, when shut off, stopped abruptly, and you can here the prop still spinning.
  3. Prickster

    SXR TOM21 Fixed Steer hood (SOLD)

    What steering and cables does this use. 1 of my guys here, not on the X, is really interested.
  4. Prickster

    Dasa, PHP, Novi, TNT, RRP, Etc. Garage Sale

    PMd about the pump...
  5. Prickster

    Lord mount

    I am turning the metal part of the lord mount if needed.
  6. Prickster

    Pin holes in cylinder!

    I have seen it a few times. Normally when someone is porting the transfers to thin. This started as a small hairline crack, hit it with a dremel on low speed, and exposed this lovely hole. Tig welded and back into service.
  7. Prickster

    WTB Aftermarket B1 ride plate

    Great, do you have any pics?
  8. Prickster

    WTB Aftermarket B1 ride plate

    Sweet, I am looking for anything smooth. No Riva Groovy or Jet Dynamics. Do you have any pics of the R&D or the what else? LOL...
  9. Prickster

    WTB Aftermarket B1 ride plate

    Is it the groovy or smooth?
  10. Prickster

    WTB Aftermarket B1 ride plate

    Looking for any A/F ride plates for a WB1. Please no Jet Dynamics. Whatcha guys got out there?
  11. Prickster

    Custom/Hybrid Wb1 & rockered sj projects

    Just use a 62t manifold with no mod, or 61x and drill out the holes. You are good to go.
  12. Prickster

    Blaster Blaster Battery Relocation Box

    I am down for 1, maybe 2.
  13. Prickster

    Custom/Hybrid Wb1 & rockered sj projects

    Doubt you will get a WB2 pipe in a B1. I am running a 781 in my B1 with a FP limited chamber with no problems.
  14. Prickster

    Engine for new build

    I have a 772 flat top Thrust motor sitting in my office. 62t/61x with an ADA head with flat top domes, new pistons and crank, fresh build. Can be sold as a short block, or RTR with dual 38s, V2 reed, and 62t electronics with a lightened flywheel. If interested PM me for pics.
  15. Prickster

    AirDown System

    15 Dollars at Home Depot. Depending on what hose size you use, they are just a 90 degree threaded pvc elbow with a pvc lock ring on the other side. You can change size and placement, and even locations. You can use the stock holes, but you will have to match the size, or make a cover...
  16. Prickster

    A nasty little gremlin

    This box was siliconed shut. Think Chris is right about the braided line.
  17. Prickster

    A nasty little gremlin

    Never thought about the braided line, great point. I have new lugs for the fix on both cables. Dug out another clean e box, solenoid, and stator. Need to get with you tomorrow for a coil and gasket.
  18. Prickster

    A nasty little gremlin

    LOL, gremlin found. And the answer Is? Crappy Chinese starter solenoid. That dirty little bastard.
  19. Prickster

    A nasty little gremlin

    Now you see why I was asking when you were getting back, and I know you have a Yami/Saki coil in blue for me, LOL.
  20. Prickster

    A nasty little gremlin

    Damn, you are the man. Thank you for the info, and I am running into the shop right now to take a swing at it. Waiting on JM to get back so I can grab a new coil from him tomorrow.
Top Bottom