Got 62t electronics and it breaks up like crazy on the top end. Stock CDI so I swapped in an enhancer that was good 3 years ago and I pinched the brown wire on the solenoid under a ground screw like an idiot. After trying for a while and finally see what i did, I put in another solenoid without...
I'm flying in for the freeride and the flights to Miami are cheaper by a couple hundred so I was wondering if anybody is coming through that direction and would be down for picking me up. I haven't gotten the ticket yet but looking for sometime on Thursday. Lemme know if you can and what you...
I've got a Tom21 FX that is -6 off the back and I am running the tailplate flush and it is perfect. Now I am starting to build my WDK F1 Pro, which is an SJ midshaft and driveshaft instead of FX like the Tom21. That puts the engine forward about 3/4" and the pump back about 2".
I'm not trying...
I've got some LC jugs that I need to replace the vents on and might do O-Rings as well. Is there something better than LC brand stuff? I've never used fuel with ethanol in it and my O-Rings are swelled up. Sometimes they leak and sometimes they try to jump out of the cap when I unscrew it...
http://slickdeals.net/f/7001808-permatex-80070-12pk-silicone-spray-lubricant-12-40-liquid-wrench-l803-12pk-dielectric-anti-seize-10-39-fsss-amazon
Loads of goodies for cheap.
Promo Code TRT25
Always a good time to buy some grease, spark plugs, vacuum plugs, different spray fluids, or even stuff for your vehicle if you take care of those too.
Here's the thread with some more codes for other dollar amounts...
I've gotten a bunch of people asking about this hull and I figure it is about time to get some pictures and info up about this thing. It's one of Tom21's first skis that he has put out in an attempt to fine tune his molds and layups and get this thing perfect. I got mine with motor mounts...
I've got some x-lace straps on one ski and am currently doing turf on my new ski. I want to switch to supremos or whatever it was that I had before but don't have them on hand. Anybody know if I set up my 4 bolts with the UFO nut like Thrust sells that it will be the same to swap out the...
US Composites has 5.7oz x 50 inch wide , 2x2 Twill Weave Carbon Fiber for sale in the discount section for $27.50 a yard and then again as 1st Quality in the regular section for $41.50. Then an ebay seller has what looks like the same one for $22.00 shipped.
I'm not concerned about looks or a...
My girl rides her bike to work daily, about 15 mi round trip, and needs a better bike for it. She wore out a couple cheapos and then a friend that was moving gave her a Specialized that she fell in love with. Neither of us know anything about bikes, so I don't know a single thing about that...
I'm thinking of throwing an OEM 155 into my girl's SJ based ski that has a limited 701. This would yield a pretty cheap mag pump with trim as I already have the pump available and the cavity is ready for it.
The downsides will be, can a limited 701 handle that size pump and can I just cut 3/4"...
I put up a website, www.carolinafreeride.com, as that seems to be the easiest way to keep information accessible. We'll still post stuff up for updates, but if you don't feel like searching through a ton of posts, just log on and check out the site.
Also, I threw some of the pictures from...
So in my quest to decide how to do foam in a new ski, I got a little carried away with some investigating. I have been in different situations where foam helped as well as where it caused problems, so I wanted to come up with the right answer as if it exists.
I weighed some of my skis...
I've got a 650 square that just started having an issue last week. It will run perfectly fine for sometimes 5 minutes or sometimes not at all and then out of nowhere, it feels like it hits hits limp mode and won't even plane. I describe it like that because it's either on or off. It'll always...
I had some problems with my stock FX-1 dying a couple weeks ago. Every time I would do a sub or fall off, not even inverted, it would barely run and usually cut off while I had to feather the throttle to try and keep it alive. It would run perfectly fine except for that 10-30 seconds of...
I broke the pole on my FX1 yesterday and I have a -4 RN pole that I would like to stick on there. I've got some UMI steering and an extra RN steering cable as well but I think that the cable is too long for the pump end. Is there any easy remedy for this?
She'll be in Swansea, Wales from the 10th through the 13th with some time on her hands and would like to hit the water in another country. She has a square although she prefers my FX-1 and even started on 550's so it won't be ruin your day waiting on that stupid girl. She really does ride...
Good times finding new trails and breaking machines.
<iframe width="560" height="315" src="http://www.youtube.com/embed/APmF_LN2C0k" frameborder="0" allowfullscreen></iframe>
Let's get some numbers going for what to expect this year. Getting towards a month to go! We need to get food and drinks planned. Also we will stake areas out for people that want to be in the center of things and areas for people that want to be away from the center of things.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.