Search results

If anyone could provide me with some quick input i would appreciate it! Im trig to drop my ski off to paint today and this is the last thing holding me up! Ive tried for hours to remove the OEM exhaust bezel and can't get it off. Ive cut through all of the silicon and gasket that sealed it to...

What are you guys using for gloves in cold water? Im in AZ but im a baby when it comes to cold water and the Jet Pilot gloves I bought are thinner than the MX gloves I wear! Any suggestions?

I plan on doing a Jettrim mat kit with rail caps on my SXR and am trying to find the replacement bumpers people are using like on this ski: http://www.pwctoday.com/showthread.php?t=374473 Ive seen it done on quite a few boats but cant seem to find where they get it from. Could anyone point me...

It seems the general consensus when it comes to stand ups is that the more forward you shift your weight the better, but in my little amount of personal experience (50-60 hours on my SXR) it always seems that if i shift my weight forward the rear end is more likely to slide out and if i put more...

Rebuilding my 07 SXR because its down to 120psi and its a little tired. Going to rebuild the engine completely with new gaskets, seals etc. but I'm debating about doing a few mods while i have it apart. I will be racing the stock class for 2015 and I've heard great things about Group K's 849cc...

Bought my girlfriend a mint condition ( less than 10 original hours ) 2007 superjet and i can't figure out how to turn the damn thing. I would like to keep it from sliding around like my 550SX does and get it to actually turn when i lay it over. I know it will never be as effortless as my SXR...

December 15th of 2013 I suffered a broken hip, three fractures in my pelvis, and a burst fracture of T12 which sent bone fragments into my spinal cord paralyzing me upon impact after bailing from my MX bike 20ft in the air. Fragments were removed, feeling and movement slowly came back throughout...

Will be installing a versiplug-R and want to know if it will drain well enough to allow me to remove the stock bilge? Id like to remove as much clutter as possible from the engine bay if I can, thanks in advance

Picked up a mid 90's Shorelandr two place couch trailer that i want to make some changes to. I plan on moving one of the wide sets of bunks for the girls couch to the center and having two narrower sets on the outsides for the stand ups so i need 6 more bunk mounts. Problem is I would like to...

After a couple burst fractures in my spine and temporary paralysis due to motocross I've made the switch to jet skis in an attempt to find a similarly addicting hobby that my newly fused spine can tolerate. I picked up an 07 SXR 100% bone stock and have a few questions regarding cleaning up the...

I removed my lanyard kill switch on my 750sx and now my ski won't turn over or even click. I tried crimping the remaining two wires together and still nothing. Im trying to get to the lake today so any input is appreciated.

So I just replaced my driveshaft bearings and I noticed the shaft has a lot of vertical play at the pump end. There is about 2 and a half inches of movement, but thats because the shaft tubing is stoping it from going any further. Wondering if someone could provide some insight as to wether this...

So I just replaced my driveshaft bearings and I noticed the shaft has a lot of vertical play at the pump end. There is about 2 and a half inches of movement, but thats because the shaft tubing is stoping it from going any further. Wondering if someone could provide some insight as to wether this...

Could anyone give me a ball park estimate of the cabosil to resin ratio. Im working in 100 degree heat so Im forced to work with small amounts of resin at a time and i need to get a uniform coat over the entire bottom of the hull. The shop i bought it from had no idea but stressed that i needed...

Has anyone ever mounted the start/stop switch into the dash in place of the primer? There isnt much room behind the dash but maybe someone could give me ideas? Any input is appreciated

So my 750's hull is beat, bad. I need to redo the entire bottom of the hull and Im not sure if it would be better to just pour on resin or use a resin based fiberglass filler such as kitty hair or fibril. Any input is greatly appreciated!

Wondering if someone could provide some insight as to how much play there should be at the pump end of the drive shaft if any? My impeller grooved my pump pretty good and I've been told it is from bad drive shaft bearings. I have about 1 to 1 1/2 inches of play. Any help is greatly appreciated!

Just curious how much the average one color paint job is, just started a build and I plan on getting it painted a charcoal grey with electric blue accents. I realize there are numerous factors that will influence the overall cost, but i just wanted to get ballpark idea on how much i will have to...