Yamaha Billet

[getreal]

I made another run of the Accustomed for the Blasters.They still look the same; there are now 4 bearings; (2) sealed needle bearings and (2) thrust needle bearings with hardened back-up washers, this design also allowed the area of the stops to be increased by 20%. All the aluminum parts are polished and then clear anodized; they are $ 475.00 + shipping.

Along with a few other items:

Fuel Fills $89.95 / Locking Fills $99.95
Fire Extinguisher / Storage Covers $99.95
Seat & Hood Latches $39.95 ea
Grab Handles $29.95 ea.
Ignition Covers (2 pc.) $199.95
Billet Heads with domes $249.95
I also have the Ignitions Covers for Kawasaki 650 / 750.
Everything is polished and anodized.

 

[getreal]

[FONT=&quot] last couple of pics.
The Ignition Covers are 2 pieces and "o" ringed. [/FONT]

 

[DirtyJ]

Blaster parts

Those parts are beautiful!!!:biggthumpup:


Thinks I may be needing some

 

[getreal]

I have more items to come.
Most of these I made in the late 90's for myself and a few friends, The Accusteer Steering's were the only thing that made it to market, (thru White Brothers). My business went a different direction but now I have the time to do it the right way.

 

[SUPERJET-113]

Thats some real quality looking stuff. Those Accusteers sell well to the X-2 and Blaster guys, since the UMI steering systems are very rare these days.
Gordon had a ton of them, but I think hes out.

 

[#ZERO]

Stupid question but can the flywheel be removed with the front section detached on the timing cover?

 

[getreal]

NO:
For that to happen the hole size was to large for the cover to look very good.
I made one and didn't think is was that important. You can still run the motor and/or check the timing.
If it really matters, making some is possible.

 

[Freakrider]

one word....NICE !

 

[steveyz250fpilot]

Do you have any flywheel covers without engraving?

 

[GIL]

Do you have any flywheel covers without engraving?

one of those timing covers would sure look sweeeet on that new 8mil !!!

 

[WaHoo_1]

WOW, PIMP stuff! :bananajump:

 

[getreal]

Do you have any flywheel covers without engraving?

YES: I can also do custom engraving.

 

[joesuperjet]

NO:
For that to happen the hole size was to large for the cover to look very good.
I made one and didn't think is was that important. You can still run the motor and/or check the timing.
If it really matters, making some is possible.

It's looks awesome but I would want to be able to remove the Flywheel thru the cover, to make it "worth buying" for me. Becides the Bling factor... Never the less it's still a great idea and so is the rest of your stuff. Might have to get some of those gas caps.... You should make some rear exhaust kits too while your at it.


JAM

 

[LBE]

Great parts!! I like the removable cover for the flywheel housing. You can change your timing easily and is great for grease/maintaining the bendix.

Verry nice!

 

[750SX]

Sweet stuff! Is the removable cover on the front cover o-ringed as well? I couldn't tell from the pics.

 

[getreal]

yes. the cover also has an "o" ring

 

[restosud]

very nice stuff!

 

[shawn_NJ]

Amazing stuff! Any chance you are going to do an X2 steering run again? The one I got from you a few years back is still perfect, even after 3 seasons of saltwater.

 

[getreal]

Amazing stuff! Any chance you are going to do an X2 steering run again? The one I got from you a few years back is still perfect, even after 3 seasons of saltwater.

I was going to do another run for the X-2. The problem is that I need to make at least 25 to be cost effective @ $475.00 ea. Everyone I talked to didn't want to pay that much. I'm still open if things change.

 

[shawn_NJ]

Ouch! I'll probably order a front cover off you when I get back from FL.