Search results

Take both and ill throw in the aluminum trailer Description of ski with Gen 2 Nose: 701cc Miller ported motor, Riva pipe, hi comp head 185 each jug, custom waterbox, custom exhaust outlet, skat 9/17, scoop intake grate, reinforced one piece hood, UMI steering and bars, Blowsion seat...

Thanks guys i actually measured it and found an exact gasket on the site used in the linked post. In case anyone else runs into this problem, i found the gasket at http://www.mcmaster.com/mv1459975500/#9464K114

hey bud im looking for 2 gaskets for a Hi Comp Protec Head on a yamaha 760 unfortunatly i have no idea what the dimensions are.

hey all i have a Hi Comp Protec Head on my blaster 760 (64x) I can seem to rind a replacement o ring for the domes. does anyone know where i can find these or a similar replacement??? Thanks guys

@2thelake good! i'm glad my post could help you get your running again!

2thelake: i did all of this because my solenoid wasnt not clicking. The way a solenoid works is that when power is applied it clicks into place and completes the chain in the two big red wires on top. If it does not click it is either not getting power, not grounded, or is not working. my...

I have a water proof back pack that i keep items like rope, jumper cables, area maps, fire extinguisher, 2 pelican cases first case: screw drivers wrench pliers ext. second holding extra spark plugs phone license fuel filters and extra parts. I through my helmet in the back strap it on and head...

ok guys i fixed the problem and im going to explain my process of elimination so that everyone that reads this will understand and hopefully find my method helpful. First: i tested the battery and found it was working properly and that my fuse was also working (replaced fuse anyways for good...

ok guys i fixed the problem and im going to explain my process of elimination so that everyone that reads this will understand and hopefully find my method helpful. First: i tested the battery and found it was working properly and that my fuse was also working (replaced fuse anyways for good...

so heres waht ive gathered. i hooked the solenoid up, pulled the brown wire and connected it straight to the battery. nothing. this means it must be on the ground. tested wires back to the ebox where all the ground are conneccted. im assuming the ground wire going to the stator if fried. im...

update. with the continuity tester: solenoid is working. Starter is working. fuse is fine. battery is good. start switch is good. killswitch seems to not have a circuit but when jumped from the ebox still will not fire. i am going to spend my saturday testing every single wire in the hull. any...

update. with the continuity tester: solenoid is working. Starter is working. fuse is fine. battery is good. start switch is good. killswitch seems to not have a circuit but when jumped from the ebox still will not fire. i am going to spend my saturday testing every single wire in the hull. any...

bump

bumb

battery is good even used an extra battery i have. the fuse is fine. also pretty confidant in my grounds but i will recheck tomorrow.

fuse is good. when relay clicked it was fine. replaced starter... started like a champ for about 10 seconds. then everything died. im going to recheck my grounds tomorrow but i was pretty confidant in them before this problem. also battery is full also have a backup full batter i double checked...

so i posted this is the blaster forum as well wasnt sure the best place for it: Ok everyone i know this could one of a few problems but i figured i would explain my situation and see what i can get as far as suggestions. I have a WB1 760 recently my starter went out (solenoid clicked when start...

Ok everyone i know this could one of a few problems but i figured i would explain my situation and see what i can get as far as suggestions. I have a WB1 760 recently my starter went out (solenoid clicked when start button was pressed and again when released) so my solenoid was clearly sending...

Right now im using an acid battery for both of my blasters but am going to replace them this week. Looking at gel and also AGM (Absorbent Glass Mat). What are your suggestions?