Search results

Let see how do you have set up your surf ski tray with foot holds or straps. What type foot holds, strap, underpading and how thick, how is your rear foot seated upon flip etc.. This is for surf riders, riding surf stance. Cheers!

How do these 2 compare? I love my DASA 950 8 mil but getting a bit tired of blow up every 50 hours on the clock

A question that has never been asked before: Amsoil Dominator or Klotz R50? for high performance engines, strokers etc..

A quick recap of todays sesh at Jupiter Inlet, South Florida. Make sure to check out and like Seth's page at Spectrum Innovations :) https://www.facebook.com/pages/Spectrum-Innovations/158529887540940

What are the common symptoms of MSD enhancer going bad? How can you test it out?

Engine sat on the shelf for over a month. I don't remember of having the leak when I took it off the ski. Is that normal from engine seating for longer time or I should replace the crankshaft seals? Also this BB engine has been used for only a season. It was sold to me as new, however I had a...

Can someone post an update? Any vids? Thanks! D.

This was one of these days when we love them here in Florida :) p.s. it might get boring after the first minute but the end is epic :)...

Whats up gang, wanted to share some cool pics from over the last couple days at South East Florida coast. As usual conditions were choppy and nasty just how we like them :)

Hey guys, any idea what jets, n/s go for 701 with ada head, stock 38s, stock arrestor? thanks

I have a couple months old ignition coil/wires. The reason I replaced it was ski was losing half way RPM after some time in the salt water. It felt like rev limiter was hitting at half way Same thing happens now. Last night after I got back from riding and ski was still salty wet, I started it...

Hey guys, I wanted to give some recognition to my a/m hull and its Builder The Watercraft Factory. Last few days we had some awesome surf conditions in the SE coast of Florida so here are some shots of whats up with the Vision :) The carbon one

Trying to find the guy/thread selling the tiny bilge switches.. Any help please? thanks!

Hey guys, if anyone is interested in the Vision Hulls by The Watercraft Factory, you are welcome to demo it in the surf tomorrow (surf riding demo only, no air please :) ) My engine rode like a crap today at the end, I hope a new ignition coil will take care of the problem for tomorrows sesh...

Hey guys, Yesterday was the first time of my new ski in the ocean. Surf was awesome, big waves (7+), small ones, steep, all kinds. The minute I went in the open I felt the ski like I've been on it for 5 years, instant bond :). 10 minutes after little brap warming up, ski goes for its first...

Hey guys, I finally managed to put my new ski all together and test ride it in the lake. Hull is Vision 2 -4" built by Watercraft Factory with longer (surf) ride plate. Engine is Big Bore 771 by Jetworks, dual stock 38s Mikuni carbs. Mag pump, msd enhancer, bpipe, 10/16 hooker prop, works...

Hey guys, I and my buddy have big bore motors built by different builders. Both of them have this knocking sound that causes bigger vibration than a stock 701. The stock 701 runs much smoother and with less vibration. Is that sound normal and common for big bore engines?. What's th feedback on...

Anyone here running that motor with stock 38s? What is the approximate adjustment I should start with? I got the jetting as follows: H 145, L 75, needle/seat 2.0, pop off spring 95 grams. Carbs measured 25 psi pop off pressure. Thanks! D.

Hey guys, I just wanted to share with all of you my excitement about my new Vision ski built by The Watercraft Factory. I am riding mostly surf down here in SE Florida, however I decided to go -4 length and have 2 ride plates: longer for the surf days and short for the flat days. It is a glass...

The piston on the right side was replaced 3-4 months ago, the one on the left was pulled out yesterday. Both times I took the motor apart for different reason and find pretty much the same wear on the same spot of the rear piston. Any guess or similar experience?