Search results

Hey yaw, For those of you who have a Push 155 setback pump or something similar, what size NPT cooling fittings did you drill and tap the pump for? I would like to go with 2 x 3/8" NPT to 1/2" barb fittings rather than 1/4" NPT, for increased flow, but they feel a little large. I was hoping to...

Hey yaw, Has anyone tried the Thrustone 155 Setback pump? What did you think? Also how do they compare to some of the other brands like Torrent? The price seems really reasonable.

Hi, Does anyone have a recommendation on a particular lifting sling that works well with aftermarket hulls? I have a Rickter XFR that I would like to be able to hoist on and off of my dock via a davit. It looks like most of the slings out there are designed for bond rails that wrap around...

Hey yaw, So I just ran into another issue to add to the list before I can get on the water this season. I was getting ready to set up my Raptor trim and I took a look at the tail end of my aluminum thru hull exhaust pipe and what do I find but this tinny spot of corrosion, or at least that's...

Hey yaw, Does anyone know where I can order the extra thick Mikuni Check Valves?

Hey yaw, So what's everyone's opinion on Threebond 1184? I really want to use it over the 1211 since it is meant for case sealant and has better resistance to fuel than 1211, but when i tried it the other day, it seemed like it almost dried out faster than i could get everything assembled.

Hey yaw, Looking for some insight. What could cause the case sealant to fail in multiple locations on a 1000cc PV motor with only 8 hours on it? As I was getting ready for the season I found a big ass pool of oil in the bottom of my hull. Pulled the motor for a pressure test and it won't even...

Hey Yaw, Can anyone recommend a good Anodizing Company, preferably on the East Coast? I just picked up a Velociraptor Trim and I want to get the parts Bright Dip Anodized in blue and orange.

Hey yaw, Does anyone have a new raptor 2 trim in stock? I would prefer a non anodized reduction nozzle but I'm flexible.

Hey yaw, What is the deal with these damn Tornado Flame Arrestors constantly Falling apart? It doesn't seem to matter if they are Tau Ceti, Hot Product or Blowsion, granted I know those are all the same just different label. I put a brand new set of on my new XS 1060 and the tops have both fell...

Hey Yaw, I am running my first set of Aftermarket Carburetors, which are a set of Full Spectrum 50's on a XS 1060 w/ a Power Factor Exhaust (Also first's). Anyways, ever since I started running them I have noticed that they seem to make a lot more noise than say a 735 with 38's. There is what I...

Hey, For those with aftermarket Carbs where do yaw normally drill and install primer fittings? I just got a set of FS 50's and it appears the location where they normally go is partially blocked.

Hey yaw, I'm curious what does everyone consider a acceptable clearances when aligning the Motor and Midshaft using Billet Couplers? I know what the factory specs are but a height difference (Dim A) of 0.039" seems excessive. Personally I try to have no more than a 0.005 " difference in...

Hey, I'm working on installing/mounting strap hooks for a Rad Dudes Broni Fuel Tank in my XFR and I was wondering how some of yaw have gone about securing your aftermarket tanks. If anyone is willing to share pics of how they have their aftermarket tanks secured or has any advice from past...

Hey yaw, This past weekend I discovered that my midshaft was essentially seized onto my driveshaft. Everything still spun nice and easily but It was a royal pain to get the midshaft off the driveshaft. Ended up having to use a 10lb slide hammer. Anyways I'm trying to figure out what could have...

Hey yaw, I just picked up my first Power Factor Exhaust and I am working on fitting it up in my Rickter XFR. It seems like the top of the pipe is going to need to sit extremely close to the top of the hull in order for everything to line up nicely and I'm just wondering what other people's...

Hey yaw, I just picked up my first Power Factor Pipe recently and I noticed that the sealing surface for the lower portion of the water jacket, for the aft cylinder is pretty thin in places. Only 0.105" verses the Fwd cylinder which is at 0.150". I saw a similar post where the gasket started...

Hey, Does anyone know a good source to get translucent blue 1/2" id colored tubing? Ideally i would like the color to match that of the stuff Fast Fuel Line and Blowsion sell. Thanks.

Hey yaw, Has anyone tried out the XScream 50mm Carbs? If so, how do you like them? What are you running them on? And have you found them to require frequent adjustment to keep them dialed in? I just picked up a XS1060 and I am considering going that route. Thanks

Hey yaw, With the water temperature continuing to drop, I'm wondering if I need to adjust my water routing or potentially add restrictors in the cooling lines? I took my ski out for the first time in about a month 2 days ago and again yesterday and the water temps were around 65 deg F. I...