Search results

We put it in yesterday before we went riding, seems to be pretty good. The skis seem to be about dead even.

As soon as I get my Worx rideplate sold I'll be picking up one of yours Steve. On another note, Rob and I went out yesterday, the porting really picked it up on the bottom end, and the skis are about dead even on the top. I have about thirty pounds on him, but I feel like the ride plate slows me...

Just a quick thanks to Steve at Watercraft Factory. As some of you have read in my previous post, I blew my motor in my new superjet, rebuilt it and blew it again. Steve contacted me from WF and gave me straight honest prices on exactly what it needed. It took him less than a week to get me back...

Odyssey Batteries in stock at Riva I picked mine up today, call Pete he will take care of you!

I wonder if the 50:1 caused it? I did not ask Wammer about it. I will call him tomorrow and ask him.

Ok so I went to Wammer's shop yesterday and he was very cool about everything. He let me work in his shop and rebuild my entire motor. I did not bore the cylinders however I did use his drill bit hone tool and got them almost perfect. I used a set of OEM pistons fresh out of a brand new boat he...

The seizure is on the intake side of the piston. Would this be a lean condion or something else?

I did not bring the ski to them. I just brought them the carbs, but they said that's all I would need. This sucks! Anyone know a good place to have my cylinders bored and honed around Delray Beach, Pompano Beach area. I don't even know how to look for one besides Riva.

No they did not water test it, but Kevin told me I have all the same mods that they put in thier Plat. Ed. ski. All I would need to do is bolt on the carbs and WA LA. It was running great then just died! As far as the flushing. I flush with salt away everytime I ride accept for the first time I...

Pressure test engine? The engine was never rebuilt, it's a brand new 2008! Here are some pictures. The first shot is not my boat, but it looks exactly like my set up, same water routing and everyting. I did run water out of the back of the pipe and water out of the head. My only water in is the...

Wamaltons did the jetting for me, I don't know the specs. I am premixing at 50:1

Well guys, I pulled off the cylinders and theres a big old scorch on the front cyliner! I don't know what would cause this however it's two months old and already time for a rebuild! Anyone with any sugestions please help!

PLEASE HELP! I have added the following! B Pipe MSD Enhancer ADA Grilted Head 35CC Domes MSD Coil V Force Reeds I think that's it for the engine. Today I went riding after having Walmatons jet my carbs. It was running great, turning almost 7000 RPMs. Then just died. Would turn over but not...

Thank you so much supertune! That is exactly what is happening! Now I just need to figure out the bad performance problem!

OK talked to factory they have no clue at all what the problem might be. Does anyone know if I should disconnect the factory heat sensor? Could that cause my problem?

It did that to me 3 times on Sunday when riding. Rode for about an hour. Does not do it every time.

I will check the wireing on the MSD but it was doing this same thing before I put on the enhancer. There is nothing I could have done putting the prop in is there?

I closed all of the adjusters except the bottom screw. Left it 3/4 turn open like explained in the instructions. I don't see why it sometimes has like a 2000 RPM rev when I'm trying to take off and I feel like im going to be stranded out in the middle of the lake. 60secs later it takes off.

Ok so I have installed the following on my 2008 Superjet: Factory B Pipe (with recommended carb jetting) Caps have been drilled off the carbs and correct settings for high and low Riva Air Filters MSD Enhancer Solas 13/17 Works D Plate Works Grate I have installed everything to the specs they...