- Location
- California
I went to Lowes and Home Depot and can't find any 5200. Do you guys think that Loctite PL Premium Polyurethane Construction Adhesive will work in place of 5200? Thanks.
Other Alternative for 5200?
- Thread starter dustin272
- Start date
- Location
- California
For a scupper valve matt
- Location
- Stevensville, MD
It's usually in the paint section. With body filler, super glue, and so forth. I would be really surprised if they didn't actually have it.
Buckwild12
I'm moved by DASA power!
- Location
- Chester, Maryland
It's always in stock at eBay, and it never goes bad. Doesn't hurt to have a tube around.
this stuff works real well http://www.jamestowndistributors.com/userportal/show_product.do?pid=3512&familyName=Sikaflex+291
Matty
Matty
D-Roc
I forgot!
- Location
- Dirty River Rider
Or use PC-11, it is 2 part that always cures and holds better than 5200. I never use 5200 on my ski anymore.
http://www.right-tool.com/pcwhiteppas.html
http://www.right-tool.com/pcwhiteppas.html
oxnard111
Creative RE Purchasing
- Location
- so Cali, Ventura/Oxnard area
I've always had good luck with Bostik 940FS
Frosty
New York Crew
- Location
- Western New York
a bit more expensive, but I use Lord Panel Fusor for just about everything...
http://www.lord.com/Products-And-Solutions/Adhesives/Automotive-Repair-Adhesives/Product.xml/298
http://compare.ebay.com/like/280627...fe6e84d&itemid=280627010186&ff4=263602_309572
http://www.lord.com/Products-And-Solutions/Adhesives/Automotive-Repair-Adhesives/Product.xml/298
http://compare.ebay.com/like/280627...fe6e84d&itemid=280627010186&ff4=263602_309572
Last edited:
D-Roc
I forgot!
- Location
- Dirty River Rider
i think anything 2 part is better than 5200. actually when i was a noob, i read everyone used 5200 and it was the bomb. So i used it, but didn't understand the hype. 5200 sets slow (fast cure is slow imo) and if you put it on to thick it skins over sealing out the air that allows it to set, i pulled a part off after a year of riding and it was not hard to remove and the thickest area was still not setup after a year. i actually am dead set against the stuff now and tell everyone about pc-11 or someother type of 2 part that chemically cures.
Finally,someone else that uses Fuzor! l used the 135EZ to bond hulls together.Stuff work great.Are you around the automotive repair business?
WFO Speedracer
A lifetime ban is like a lifetime warranty !
- Location
- Alabama
West System six 10 epoxy, fits in a caulking gun so no special gun to buy $15.99 at the link below, to glue a hull together plan on getting at least two or three tubes
http://www.pbsboatstore.com/west-system-six-10.htm
http://www.pbsboatstore.com/west-system-six-10.htm
- Location
- California
Thanks guys after I couldn't find any 5200 yesterday I went and bought pc11. Then this morning I read this thread and people are using it also. Thanks again for everyones imput.
- Location
- Texas
Academy carries 5200, so does Ace.. Well on the coast anyway.
Last edited:
- Location
- Granbury, TX
Yeah when I am needing 5200 or 5200 fast cure I always know they have it at Academy. I don't know how wide spread Academy is though....
- Location
- Texas
I used Right Stuff by permatex on my lines in the tray. That stuff is pretty good. I had an XPL that had the ride plate installed with it. Had to pry it off. Its expensive but I had it laying around so I used it. I use it to mount bilge pumps too.
- Location
- Montreal, QC, Canada
I would not use PL premium, not made to be use underwater, but ask for urethan sealer at your autopart. The one they use for windshield. I don't remember exactly to products number I used last time, but it was alot easier to apply than 3M products and seals great
D-Roc
I forgot!
- Location
- Dirty River Rider
that west systems is what i used to put my sponsons on. great product.