Daytona Freeride parts for sale or WTB

[King of Hack]

SOLD! Now I need a complete seat for back up I cut the other one all apart and ran out of time to finish.

i will load it up then. it will be in the rad dude trailer.

 

[Fro Diesel]

Have SN hood and several RN hoods of various conditions from rough to clean. Will bring them if presold.

I lost my sn hood in daytona years back whilst towing a sunk ski back to the beach. I would have paid a hundo to get back in the surf that weekend with a stock hood w duct tape on the intake holes.

Erokwilbs sent me a free sn hood a couple weeks later.


sent from Fro Diesel using tapatalk2

 

[stredman]

On the topic of SN hoods, anyone happen to have a modded liner available?

Sent from my SPH-L710 using Tapatalk 2

 

[ryan]

i have a stock b1 seat complete $100.00 but im not bring it with out it b ing sold.

 

[XJCrawler]

I can bring a waveblaster bpipe with mod chamber $525

 

[todc207]

i have a stock b1 seat complete $100.00 but im not bring it with out it b ing sold.

Hey if this was for me thank you a ton but I found one that is already shortened and covered. Perfect for my second boat. I bet it would sell though.

 

[hfthe3rd]

I got a new set of fiberglass foot holds . $65 . Please send me your email and I will send you a pic. Not sure of the brand.

 

[RivMan]

I've got a 61x 701, protec head, protec B1 pipe, runs great, 170/170 compression I can haul down.

It's complete from carb to pipe, with electronics.

-Rob

 

[Nuklear6]

need a coil and a start stop switch if anyone has one. already been through both on one ski now need for another. gonna order tomorrow but just figured I'd ask since earliest I'll have them from Riva is Tuesday. call or text me with what you locals have.

thanks
Chuck Palmucci

609 510 3062

 

[KTM434]

need a coil and a start stop switch if anyone has one. already been through both on one ski now need for another. gonna order tomorrow but just figured I'd ask since earliest I'll have them from Riva is Tuesday. call or text me with what you locals have.

thanks
Chuck Palmucci


609 510 3062

Have you taken yours apart? I have one that I just swapped out because the start button contacts were junk but the wiring, connectors and contacts for the stop and tether switch are good. Let me know if that helps

 

[BruceSki]

Just picked up a wetjet kraze today.

Anybody want "the" carb and intake? 46mm with reed stuffers

Or a wetjet pipe?
or a 155 psi 61x motor?
or 61x electronics?

 

[ntrsspray]

Just picked up a wetjet kraze today.

Anybody want "the" carb and intake? 46mm with reed stuffers

Or a wetjet pipe?
or a 155 psi 61x motor?
or 61x electronics?

46?


Sent from my iPhone using Tapatalk

 

[BruceSki]

isnt that what comes on the wetjet kraze motor? a single 46?

 

[KTM434]

If the intake mani says WPP on it then it's the Westcoast intake with reed stuffers and 46mm carb. The bolt spacing is different on this carb so it must be used with this mani

 

[BruceSki]

Like this?





2nd pic is a mikuni 44mm sitting on one stud. The spacing is wider and will not fit.

 

[Nuklear6]

how much?

Like this?
View attachment 207371
View attachment 207372
View attachment 207373


2nd pic is a mikuni 44mm sitting on one stud. The spacing is wider and will not fit.

 

[jnutz]

looking for a cheapish a/m exhaust for my 61x/62t... just throwin it out there

 

[Proformance1]

Any parts in my for sale thread can be brought to daytona. Last call is tues night. Ill be in wed at 12 am.

http://www.x-h2o.com/threads/123545-Yamaha-parts-for-sale-61X-cyl-pistons-bed-plates-timing-cover-cables-misc-etc&highlight=

 

[KTM434]

Like this?
View attachment 207371
View attachment 207372
View attachment 207373


2nd pic is a mikuni 44mm sitting on one stud. The spacing is wider and will not fit.

Yes sir that's the hot setup

 

[BruceSki]

so hot the paint peeled lol