E-T 1107 Dyno results

[E-Tech]

ET 1107 PF pipe , PHP crank, 49 full spec carbs
v force 3's , php intake Manifold
MSD 32 deg 17 :1 220 psi

 

[Ducky]

What happened at 6100 and 6200 rpm?

 

[E-Tech]

These are quick runs up and down. here is a adr crank dyno result.

 

[E-Tech]

Have 100's i just have to fine the 175 hp run was lean and mean 2 sec to full power.

 

[sinisterjosh209]

so nice to see real numbers on paper!!!! Dang ET makes power boys!!!

 

[OCD Solutions]

May as well do it for the 1107 as well.

 

[mike b]

Just curious why are some rpm and data missing? Like each dyno has missing data in different places and just confused why?

And also back to the first question. What happened in the low 6ks where the power cut out? Since it was so drastic of a drop

 

[stingrayguy]

Just curious why are some rpm and data missing? Like each dyno has missing data in different places and just confused why?

And also back to the first question. What happened in the low 6ks where the power cut out? Since it was so drastic of a drop

This is normal in the car engine dyno world. just a hiccup in the data.

 

[mike b]

This is normal in the car engine dyno world. just a hiccup in the data.

Wait the hiccup is the change of # or the missing rpms? I've seen little up and downs before on dyno numbers but wasn't sure on the larger one if that was just a fluke or what

 

[stingrayguy]

Wait the hiccup is the change of # or the missing rpms? I've seen little up and downs before on dyno numbers but wasn't sure on the larger one if that was just a fluke or what

Not sure, I'd guess a hiccup in the HP number. When I had my car on the dyno, out of 3 pulls, we had a couple of miss reads on each run just like the sheet above.

 

[truerider411]

I have rode this motor back to back with matching dasa 1200 and dasa 1100 Same carbs, pipe, TL, race gas etc etc and the 1107 is a very impressive motor. I would highly recommend.


Sent from my iPhone using Tapatalk

 

[Jhucke]

Curious what the results would be with novi 48s.

 

[E-Tech]

New prices on the 1107 topend kits 2499.

 

[Bobert540]

Would it be possible to make either kit work with the PHP lightweight 4mil crank?

 

[x2stroker]

Would it be possible to make either kit work with the PHP lightweight 4mil crank?

You'll need a spacer plate to compensate the 4mil crank with the 967 cylinder. Hit up @holeshot for that.

 

[erik mx45]

ART do u have the flywheel covers done ?

 

[masterblaster]

that red cover might win her a miss universe title...geterdone

 

[E-Tech]

yes i do!

 

[masterblaster]

better get your sash lined up bud

 

[hink320]

I know there aren't many videos of these motors in action. I've posted some, but I'm a mediocre rider at best. For anyone skeptical of the power that these motors make, go ahead and check out 31saif31 on Instagram. I think that will shatter any doubts that people may have. He bought one of the first ET motors and he posted a pic of 2 more that he bought shortly afterwards, so obviously he was impressed with them.

https://www.instagram.com/p/2DiruGpThb/?taken-by=31saif31
https://www.instagram.com/p/6KrtJypTkT/?taken-by=31saif31
https://www.instagram.com/p/1k5PfNJTuz/?taken-by=31saif31