- Location
- Great North West
Does anyone have or know anyone who is making the small L brackets for the wave blaster mod chamber. I see somebody is making the big flat bracket , But haven't seen the small L brackets. Thanks
Blaster Factorypipe blaster mod backet
- Thread starter MileHighJSC
- Start date
Mike W
Infidel
- Location
- North Florida
I have up looking for one. I made made mine out of a thick piece of 90* aluminum.
- Location
- Cleveland, Ohio
Post a picture of exactly you need. I might have it.
- Location
- Great North West
Here is the Small L bracket. Below the lord mount- Location
- Pittsburgh Pa
Any luck on finding this? I’m actually looking myself well I’m looking for everything but atleast if I have the l bracket I’m starting somewhere
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Quinc
Buy a Superjet
- Location
- California
Only need the flywheel cover bracket.
- Location
- Pittsburgh Pa
Ahh I see I thought you meant the one above the manifold my mistake
Quinc
Buy a Superjet
- Location
- California
That is the one the OP wants. However, the pipe will hold up fine with just the flywheel bracket. At least after multiple failed flops in the surf I havent had any issues...
Big Kahuna
Administrator
- Location
- Tuscaloosa, AL
Rad Dudes may have something that works.
- Location
- Pittsburgh Pa
I’m running a limited pipe so I don’t actually have the flywheel one but I do have the one onto the tank should I be concerned about getting the smaller bracket by the exhaust manifold? Just got the pipe and installed last week
Sent from my iPhone using Tapatalk
Quinc
Buy a Superjet
- Location
- California
Get a piece of stainless heat it up with a torch bend and drill.
Who makes the other bracket?
- Location
- Plymouth, MA
I have three of these sets left. comes with everything listed below.
1 heavy small 90 bracket. stainless don't remember thickness but believe its twice the stock FFP.
1 large half moon shape, machined billet alum, about two and half times thickness of stock FFP. If mem serves me right these will work on FFP - LTD, MOD and GP760, WB2 pipe.
1 small half bracket. stainless one and half times FFP thickness. I think this only applies to GP760 and WB2.
1 short lord mount. I believe these are for the 90 deg bracket. Not 100% sure if these are the correct ones.
2 taller lord mounts, I believe these are for the other two brackets. Not 100% sure if these are the correct ones.
Sorry for the not so perfect info but just happens to be coincidence I was cleaning out some crap and I found these the same time I read this. Short story behind this back in the day I got tired of breaking these and had my shop fab me up some super duties for the surf. I highly doubt I will run these again and make the right guess these will work for your application. Sorry i don't normally sell like this but just have to much going on.
$ 40 shipped USA and PM
Pat
1 heavy small 90 bracket. stainless don't remember thickness but believe its twice the stock FFP.
1 large half moon shape, machined billet alum, about two and half times thickness of stock FFP. If mem serves me right these will work on FFP - LTD, MOD and GP760, WB2 pipe.
1 small half bracket. stainless one and half times FFP thickness. I think this only applies to GP760 and WB2.
1 short lord mount. I believe these are for the 90 deg bracket. Not 100% sure if these are the correct ones.
2 taller lord mounts, I believe these are for the other two brackets. Not 100% sure if these are the correct ones.
Sorry for the not so perfect info but just happens to be coincidence I was cleaning out some crap and I found these the same time I read this. Short story behind this back in the day I got tired of breaking these and had my shop fab me up some super duties for the surf. I highly doubt I will run these again and make the right guess these will work for your application. Sorry i don't normally sell like this but just have to much going on.
$ 40 shipped USA and PM
Pat
Attachments
- Location
- Winter Haven, FL
Pm’d
- Location
- Plymouth, MA
one sold
lord mounts are 1" and 4"
lord mounts are 1" and 4"
- Location
- Plymouth, MA
one left
- Location
- Plymouth, MA
sold and shipped