MSD TL Enclosure Mounting options?

[Superjetjim]

Building a new XFS for 2015 and looking for pictures of MSD Enclosures installed in skis.

I'm not going with a firewall tank, will use a Jazz and small battery.

Anyone attached an MSD enclosure to the side wall of the hull without external fixings? Or perhaps the firewall without bolts showing in the tray?
Perhaps a neat tank / battery / ignition tray?

I dunno, show me what you've got please, looking for some inspiration!

Thanks in advance for any thoughts / pictures.

Jim

 

[Superjetjim]

Going with the RRP pipe as well so not a huge space in front of the XS1200

 

[JoeD]

Not mine but thought it was interesting

 

[lerott]

Why do not use rear rrp tank ?
I have rear RRP Tank, atp center battery tray and MX100 factory mount bolt on ATP tray to fix RRP enclosure box for TL MSD.
I'm pretty sure you can find pics on FB if you show Pierre Maixent pictures

 

[Little_Franny]

I don't have pictures but on my envy i took 2 of the ebox to bulkhead brackets from a RN and atached them to a piece of aluminum using coutersunk allen fasteners. I drilled big holes, prob 4 about 1 inch to get rid of material, then epoxied it to the side of the hull. so far so good

 

[speedysprocket]

 

[SpaceCowboy]

RRP has a surf enclosure its around the 400 dollar mark though. I wish Air Time Products would make and enclosure for MSD total loss like the ones that fit their flame system.

 

[speedysprocket]

Mine above cost about $30, but doesn't fit the coils or starter relay.

 

[Superjetjim]

RRP has a surf enclosure its around the 400 dollar mark though.

Yes that's the enclosure I have, just not sure of the best way to mount it?

 

[SpaceCowboy]

Yes that's the enclosure I have, just not sure of the best way to mount it?

If you don't want to drill holes plexus some studs on the firewall


Sent from my iPhone using Tapatalk

 

[JoeD]

Here's another

 

[Superjet1000]

Sent from my iPad using Tapatalk

 

[MCrider]

this is on a Aqua bot in the for sale section...

 

[McDog]

rrp box in badass superfreak. Used plexus plate to attach it to studs.

 

[ISeeWetPeople]

I run dual msd to get more power.. no just kidding=)

I have everything in waterproof box=) and i made a metal stand for the box and battery. and that stand is bolted with 4 bolts to place where battery used to be..

and the best part is that just opening 2 bolts and few deutch connectors i can lift all electrics up so its easyer to adjust ebox etc. only starter wire is stil connected and i will chage that too so i can take all my electrics to table under 2min

 

[Jetfiend]

Cool setup^ Have you had any issues with the coils being so close to the brain? Also, did you make that box? Looks nice!

 

[ISeeWetPeople]

No i have not.. Should i? For some reason i burned 2 box before this setup, after both fails i rebuild my electrics from nothing and both times middle of air my ski shut down.. So then i build this setup using this plastic ebox that i found and now that water cant get in it has workd well.. 2 years with that setup and no broblems.. But now that i will have pf pipe and tpe964 this winter i have to figure out something else. This setup wont fit between firewall and motor.. Have to tear it down.. No choice...

 

[Superjetjim]

Thanks for the contribution and pictures. It's really helped, gone with a firewall mount with plexus plate with blind studs in Ali plates bonded to firewall with adhesive sealant.