SXIPro
JM781 Big Bore
- Location
- Here on the 'X' mostly
I'll start:
Filling in the intake manifold crossover on stock 38s.
Filling in the intake manifold crossover on stock 38s.
Name a mod to your ski you wish you didn't do.
- Thread starter SXIPro
- Start date
5810
WHERE-THE-SEAT-AT
- Location
- Knoxville TN
Why, i want to do that to my intake.
me
buy a 600 dollar tbm flywheel, 0 diffrence in feel of power :-(
me
buy a 600 dollar tbm flywheel, 0 diffrence in feel of power :-(
SXIPro
JM781 Big Bore
- Location
- Here on the 'X' mostly
No matter what I tried: messing with my highs and lows, even rejetting, I couldn't get that nice smooth powerband I used to have, and it bugged the crap out of me. I bought another stock intake mani with the crossover still in it, slapped that on, and all is right with the world again.
Wanna buy one that is filled in?.....Cheap?
BruceSki
Formerly Motoman25
- Location
- Long Island
Damn now you have me worried. Good thing I still have a stocker on the shelf. Do you have aftermarket reeds or stuffers?
What was your engine setup and what jetting were you running? Open flame arrestors or stockers? What size springs? popoff psi?
What was your engine setup and what jetting were you running? Open flame arrestors or stockers? What size springs? popoff psi?
- Location
- So. IL
2 Things rank right at the top....
Going with a -4 inch pole. I already had a -3 inch steering setup. SO to me -7 is WAY too far.
Selling my freestyle Speedwerx pipe.
Going with a -4 inch pole. I already had a -3 inch steering setup. SO to me -7 is WAY too far.
Selling my freestyle Speedwerx pipe.
- Location
- Edmonton, AB
how does the speedwerx pipe compare to a b-pipe?
DAG
Yes, my balls tickled from that landing
- Location
- Charlotte, NC
have not done:
wide trade mod
-2 hull
bilge switch on handlebars
wide trade mod
-2 hull
bilge switch on handlebars
suva
57
- Location
- Just south of the Citadel, Idaho
Side exhaust, Rev hull, waterdawg 66E stuff, dry pipe on the SXR.
jetkid
Paul Lambers
- Location
- Grand Rapids MI
scupper tube, MSD cdi, also I did not use thick enough padding under turf.
steve-uk
Manners cost nothing
- Location
- Barrie - ontario
TBM Pump cone... would have been better sprinkling pixie dust in my pump
- Location
- Down stream of Harrisburg, PA
i'm wishing i bought a ski that's RTR. something like a superfreak/wcf/wamiltons/xs. so to answer your question- all of them? lol
SXR-FOREVER
Finally Flippin
- Location
- Lake Minnetonka, MN
blowsion handlebar mount bilge switch
OCD Solutions
Original, Clean and Dependable Solutions
- Location
- Rentz, GA
X-Scream SS865 engine....by far the worst mod I ever did. Ever since installing the 7 port billet powervalve motor i cannot stand to ride any other ski without a team scream engine. Now everybody wants to ride my ski and leave me with their broke azz ski whle they ride around in ectasy. Worst mod EVER!!!!! :banghead: :banghead:
5810
WHERE-THE-SEAT-AT
- Location
- Knoxville TN
:haha: LMAO lol
steve-uk
Manners cost nothing
- Location
- Barrie - ontario
x2 its way too much power... much prefered my stock 701
steve-uk
Manners cost nothing
- Location
- Barrie - ontario
yeah i had mine for half a season... my buddies were more pi$$ed than me as i was filling up every 30 mins or so!
Bobert540
Site Supporter
- Location
- Rockford,MI
Your hull is fine you just need to fix your motor! Lol
- Location
- So. IL
Speedwerx= no tuning no fuss just power from the bottom up
B-pipe= tune it, adjust it, fiddle with it and it still don't hit as hard.
Do a search and see if you can find any complaints.. Everyone says that they kick anus