Parting out Dasa 1100, CPT 836, 10/18 155MM Prop

[Mdavies_02]

So this year I went from my 4 year setup of a Super freak CPT 836 to parting it out and buying a built Rickter 1100 and putting in a new PHP898 setup. It is now time to sell off all the extra engines, and parts.

• DASA 1100 built by Kyle at 911 Engines - PENDING

DASA billet top end with PV, Dasa head, 240psi per hole, 5 hours on setup, bed plates included $3900 USD plus shipping - Exhaust mani, intake mani, and carbs seperate

• DASA 48’s on manifold $1000 USD plus shipping - SOLD
• 155mm Large Hub 10/18 Prop – Came with the Dasa 1100 and worked great. $270 USD plus shipping
• CPT836 with PHP 4mm Crank – Rebuilt by CPT in spring of 2019 top and bottom end

ADA Full girdled head, 185psi per hole, approx 50 hours bed plates included $2400 plus shipping

• Power Factor Pipe with manifold, rickter coupler, clamps, strainer, flow control, waterbox. $1100 USD plus shipping - SOLD
• ATP TS 2 TL in ATP Billet Ebox $600 USD plus shipping- SOLD

Had a bad Bendix this year and it has scuffed up the TL Flywheel pretty good on the face. System works great and has deutsch connectors for stator and start/stop. I’ve had the system for three years and loved the control and dual curves. Come with cable and software to program new curves. OEM relay

• Limited Slip Tank – 4.7Gal with built in Battery box. No straps. $280 USD plus shipping- SOLD

I'll post up pictures tomorrow. Had a ride on the ski today that ended unfortunately. I left my Iphone on the nose and noticed it fly off at about 8' deep of water. Searched for about half hour with mask and snorkel. Not sure what I had backed up but it may be awhile to get compression pictures on everything now that its parted out.

Hit me up with any questions

Cheers and have a good Friday night

Mike

 

[Sledfreak9944]

Interested in more info on the 1100 sent message

 

[Mdavies_02]

PFP - Sold

Dasa 48's - Pending

Limtied Slip - Pending

More pictures added.

 

[jetpilot36]

no case porting on the 1100? didnt see any epoxy

 

[Mdavies_02]

no case porting on the 1100? didnt see any epoxy

The top section cases has been expoxied. The interior of the flywheel housing has been painted silver. Its hard to see. I'll snag a better picture.

 

[Mdavies_02]

TTT.

Here is the prop. Looks like the previous owner used some heat. Could be cleaned up abit but ran great.

 

[Mdavies_02]

Dasa 1100 is pending payment

Here are picture of the CPT 836

 

[Mdavies_02]

Dasa 1100 sold and shipped out. Bump


Sent from my iPhone using Tapatalk

 

[Mdavies_02]

Bump. Looking to get ride of the 155 prop, and CPT 836

Also will have a Thrust 144 EZ trim system for sale once I get pictures.

Cheers

 

[brapp226]

TTT.

Here is the prop. Looks like the previous owner used some heat. Could be cleaned up abit but ran great.

PM

 

[Mdavies_02]

TTT.

Still gotta post the trim.

 

[MikeMcDermid]

TTT.

Still gotta post the trim.

Post the trim on so*on. I have had a bunch of people asking if my 155 trim would fit their superjets

Sent from my SM-G973W using Tapatalk

 

[Mdavies_02]

Post the trim on so*on. I have had a bunch of people asking if my 155 trim would fit their superjets

Sent from my SM-G973W using Tapatalk

Thanks for the bump and the motivational push. I be lazy.

 

[Mdavies_02]

Thrust EZ Pull 144-148 Trim up for sale with never installed cable and half season old back trim lever. All Thrust

500 usd plus shipping

 

[Mdavies_02]

Thrust Trim Sold


Sent from my iPhone using Tapatalk

 

[Jyzmbe]

Still have the 155 prop?


Sent from my iPhone using Tapatalk

 

[Mdavies_02]

Still have the 155 prop?


Sent from my iPhone using Tapatalk

Yup. Could have it to you in 4 days for $290 shipped (to Plano TX). Let me know.