SN SJ surf project

Etheraldreamer

Etheraldreamer

Be there and be square.
Location
Spring Hill, FL
Finally months later got it together and out on the water for the first time...rebuilt from the ground up.

Motor:
-61x case w/hot rods crankshaft (need a 62t case)
-61x Cylinders ported on stock 81 bore for now
-ADA Billet Girdled Head with 35cc domes
-B Pipe
-MSD Enhancer
-MSD coil
-Mikuni SBN46mm Carb w/choke removed and primer fitting installed (also Riva Throttle wheel)
-Boyesen power reeds
-K&N flame arrestor
-TDR Waterbox
-Jet Works flow valve
-Replaced every inch of fuel line with higher flowing clear fuel line (figured it would make trouble shooting easier)

Hull/Other:
-Worx Intake grate and rideplate
-Solas 14/18 Concord Impeller w/billet nose cone
-Wamilton's Stubby pump cone
-Waterdawg REV Footholds
-Hydroturf inside the tray with nice thick pad to save my feet on my flat landings in the surf
-UMI 4 Degree steering w/Blowsion throttle and ODI grips
-Re-upholstered my chin pad with black 4way vinyl
-Black billet Blowsion bow eyes/bilge fittings/water bypass

thats not all of it but covers the meat and potatoes...ran great today...just need to take the time and get the carb more fine tuned. Did all this at once so I jumped from stock to this thing and holy crap was it worth it!

will post some pics when i get some.
 
Etheraldreamer

Etheraldreamer

Be there and be square.
Location
Spring Hill, FL
couple of small changes...have gone with 2 bypasses for the cooling and bolted on some ratchet straps to hold the hood in place. finally have it tuned pretty close to perfect. few small kinks i need to work out but nothing major...still need to post some pics.
 
Etheraldreamer

Etheraldreamer

Be there and be square.
Location
Spring Hill, FL
without further ado

here are a couple pics of the ski...in nice dirty just ridden shape :)

First an overview of the motor and my weight saving single gas tank strap...
IMG_0084.jpg


View of the tray.
IMG_0079.jpg


Closer view of the REV footholds/turf job, pardon the sand this is like 30 mins after coming out of the water.
IMG_0080.jpg


Tuning the low speed...getting pretty close
takeoff.jpg


Just playing around once i got the tuning dialed in
bunnyhop.jpg
 
Fro Diesel

Fro Diesel

creative control
Location
Kzoo
I am liking this ski. reminds me of my ski...even though i tore it back apart once i got back form daytona. So only kinda like my ski. I need to get my ada head put on looks like so i can keep up with ya at chicken bone. Least there should be a few of us sn standup riders there.
 
P

primetime1267

AMSOIL Dealer
Location
Sarasota, Florida
Nice job bro.... I have just started working on my SN project again.. I took 6 months off from working on it.. I will start a new thread later this week.. We def. need a SN only thread..
 
Etheraldreamer

Etheraldreamer

Be there and be square.
Location
Spring Hill, FL
Just added Blowsion's internal fuel filler/pickup and also got a black billet blowsion cap for it. pics of that when i can get some. it looks sweet and makes it so easy to fuel up with my VP jug. Also i just glued all the edges of my turf down and cleaned up the foot mold sections that where starting to peel down with the toughened rubber glue blowsion sells...its GREAT stuff.
 
Last edited:
Etheraldreamer

Etheraldreamer

Be there and be square.
Location
Spring Hill, FL
the other end i did kind of wrong on account of time. i just hacksawed off the hooks took out the pole bolt and slid the pole bolt back through the sewn loops of the webbing. not the best way to do it but way better than nothing. i mean to eventually take the hood hooks up and secure them under those.
 
You must log in or register to reply here.
Top Bottom