sxr freeride build

[Bigfish]

Started my build in March then had to have knee surgery .Back to where i can get around so back at it.I did get the engine out and apart before the knee and sent to jetworks.
THIS WAS MY OLD SET UP ,WF FOOTHOLDS,WET PIPE,VILDER FLYWHEEL,BORED NOZZLE,SMALL CONE,9/17 PROP,
Plans are
LIGHTEN SOME PARTS
XFT SCUPPER
INTERNAL FUEL FILL
SKAT PUMP
DUEL 46 CARBS
CYLINDER AND CASE PORTING
TBM FLYWHEEL AND ADVENT
ADA HEAD

XMETAL POLE

 

[Proformance1]

Very nice, keep us posted on how it goes and if you are keeping track of the weight. Why are you changing flywheels?

 

[Bigfish]

The vilder has timing advance built into it(7 degrees )ill be using the advent for a better curve.

 

[Kawi 800]

I have an ADA head and 28CC domes, huge inporvment.

 

[Scorn800]

Who will be porting your motor?
Good luck with the Build!
Go Green!

 

[TB]

he said he was sending it to jetworks so i would imagine art's doing the porting

 

[Proformance1]

The vilder has timing advance built into it(7 degrees )ill be using the advent for a better curve.

Ahh, I didn't know that, very good choice. some of the aftermarket curves are very good. I've got the Mitsubishi 9R, I think it made more of an improvement than the wet pipe.

 

[Bigfish]

Got all that extra glue ground out,made a block off for fuel filler and covered the nose with turf those covers from blowsion or trinity are high dollar.

 

[Bigfish]

Ahh, I didn't know that, very good choice. some of the aftermarket curves are very good. I've got the Mitsubishi 9R, I think it made more of an improvement than the wet pipe.

I have run vilder for years(1996-2007) great flywheel just wasn't going to work with this setup .Worked great in my 750 and 800 its going in another engine for my x2 next project.

 

[Proformance1]

How much weight did you save by cutting the glue?

 

[Bigfish]

How much weight did you save by cutting the glue?

I haven't got a clue

 

[Kawi 800]

You can cut out the front section of your hood for a good -6lbs

 

[Bigfish]

You can cut out the front section of your hood for a good -6lbs

Thanks for the info.I might do the same to mine.Lightened the battery tray and ebox bracket up.

 

[Bigfish]

Nothing new with my build waiting on parts so i decided to put a pic off my girls sxr up.

 

[Proformance1]

Thanks for the info.I might do the same to mine.Lightened the battery tray and ebox bracket up.

Wow very impressive work! Keep it up and start keeping track of the weight. Or at least let us know how it all adds up in the end.

 

[Bigfish]

Wow very impressive work! Keep it up and start keeping track of the weight. Or at least let us know how it all adds up in the end.

Thanks after all the holes 1 1/4 pounds lighter :beerchug:

 

[crammit442]

Nothing new with my build waiting on parts so i decided to put a pic off my girls sxr up.

Cool! Here's a pic(thanks to Ronny) of your girl on my boat!:fing02:

 

[Bigfish]

Cool! Here's a pic(thanks to Ronny) of your girl on my boat!:fing02:

I thought Erica sent them to youfound out she didn't ill send them to your email tonight.:biggthumpup:.Have you got the engine for the sj .

 

[Bigfish]

:woot::woot::woot:Got some parts

 

[Proformance1]

Wow, skat, XFT, TDR, TBM, Blowsion, very nice, someone hit the lotto.