xmetal chinpad

[DR3]

hey guys whos makes chinpads for the xmetal pole thats worth buying??

my buddy just bought a WF and i am not impressed at all :no: pretty bad fitment issues

i know 24-7 made one and i think CG??

thanks Danny

 

[FL-cracker]

Has he talked to Steve.... something doesnt seem right?

 

[DR3]

My CG Racing pad is awesome! and if you ask Chuck, he'll even put a sweet little customized personalized touch on it for ya!! :beerchug:

how much?? website? number?:bananajump:
i have seen these and like them

Has he talked to Steve.... something doesnt seem right?

yea, i think hes calling him tomorrow and hopefully he'll take care of him but it was crooked as heck :thinking:

 

[DAG]

i got my WF pad and was dissipointed when it did not have the allum center support.. it was teh main reason i went for his pad so i called and got the "I normally dont put those on if not asked to" even though his website clearly states it is included...

I tryed to go CG, but i called 3 times and send PM's and nevr herd back to this date... to bad pat doesent make a pad.. i'v liked everyhting 24-7 has put out. but again hard to get ahold of

 

[waterfreak]

hey guys whos makes chinpads for the xmetal pole thats worth buying??

my buddy just bought a WF and i am not impressed at all :no: pretty bad fitment issues

i know 24-7 made one and i think CG??

thanks Danny

please have him give me a call. I'm sure I can sort it out for him

 

[2lick]

cg is a good price too like around 90 i remember

 

[DR3]

please have him give me a call. I'm sure I can sort it out for him

he should tomorrow, we were going to try and make it work but he was hoping you would take care of it for him b4 having to go that route

Call Kevin@Legdrag. I'm pretty sure he sells the CG pads now.

sweet, i could almost make out the # from the pic:beerchug:

 

[waterfreak]

I never had a problem with the chinpad but there are a few simple steps to take to properly fit it on the pole:
1- properly cut the tabs to allow for enough clearance.
2- center the pad before making your holes
3- make sure you install a bolt (drill and tap)on the top front of the chinpad

I know that I need to hand out installation instruction but the x-metal web site does a pretty good job of it.

 

[waterfreak]

i got my WF pad and was dissipointed when it did not have the allum center support.. it was teh main reason i went for his pad so i called and got the "I normally dont put those on if not asked to" even though his website clearly states it is included...


I apologize for the mis-cummunication and I realize the web site is a bit out dated but we will be totally re-designing it (web site) with updated pics ,prices
and hopefully isome nstructional pages

 

[DR3]

i hear ya but the v-shaped sides that came down were not the same on each side (one further forward and shorter than the other) and if bolted up where the points are now the pad would be crooked or might not even have enough meat to bolt up to at both sides if pad was straight

pretty easy install, pad was just trimmed a lil crooked

 

[DR3]

kinda like this, maybe not this bad but you get the idea, not enough meat to adjust both sides either

excuse my drawing skills :masked:

im sure youll take care of him, cant be perfect everyday!:biggthumpup:

 

[crammit442]

i got my WF pad and was dissipointed when it did not have the allum center support.. it was teh main reason i went for his pad so i called and got the "I normally dont put those on if not asked to" even though his website clearly states it is included...

I tryed to go CG, but i called 3 times and send PM's and nevr herd back to this date... to bad pat doesent make a pad.. i'v liked everyhting 24-7 has put out. but again hard to get ahold of

Chuck was in a car accident a month or so ago and had to have surgery to repair a crushed ankle and has been out of pocket a bit. He also has a compression fracture in his back.:frown: Leave him a message and I'm sure he'll get back to you as soon as possible. He's beginning to get a bit of mobility back and should be slowly getting back up to speed now. His chinpads are nice and come with all the hardware needed to fit right on.

 

[oxnard111]

I am presently purchasing a chinpad for my x-metal pole from ucsspirit

he says he doesn't make too many of them, and mine is getting finished here in the next day or two... there are some pictures in a thread I started about a week or two ago.

X-metal pole chinpad help... please