Yamaha 5mm stroker crank and matched 62t cases, girdled head

[way2manyhobbies2keep]

SOLD

Picked this up in a parts lot from an old freestyle guy, unknown builder but I believe it all came out of Veys powersports.

Koyo bearings all spin nice, rods look good, no play. Obviously needs assembled and seals.

Cases are clean, epoxied and ported, studded for use with the included girdled head which comes with 760 domes 35.4cc's (needs orings)

Asking $900+ shipping, more pictures below,

Selling because I'm a less power less problems guy,

I prefer to be contacted via txt at 619-307-0474

Lowballers will be sent nudes of Matt Depalma

 

[way2manyhobbies2keep]

more pictures

 

[way2manyhobbies2keep]

More pictures

 

[jetpilot36]

do you know what head that is?

 

[TheBuzzard]

do you know what head that is?

Same head as PPI performance products incorperated only no logo. I've had a few

 

[schicks]

Very cool, square cut domes on top, wont spin oring tightening plugs.

 

[way2manyhobbies2keep]

Very cool, square cut domes on top, wont spin oring tightening plugs.

Yah, I would love to find more dome options, the head is large marge, but I like how modular it is

 

[way2manyhobbies2keep]

Man the forums are a bit slower than they used to be

 

[TheBuzzard]

If I remember right , the water flow thru it is weird too. Has 2 separate water passages that have to be routed right to get correct flow

 

[way2manyhobbies2keep]

Bump still for sale

 

[crisqob]

Hey gang I'm a total newbie...... I'm just going to go ahead and apologize now for my guided ignorance. Will your parts bag retrofit to my Yamaha 650 block? I believe I have 6M6..... not 62T. Does that matter really?

Thanks for no bashing me too bad on my very first post.

 

[way2manyhobbies2keep]

Hey gang I'm a total newbie...... I'm just going to go ahead and apologize now for my guided ignorance. Will your parts bag retrofit to my Yamaha 650 block? I believe I have 6M6..... not 62T. Does that matter really?

Thanks for no bashing me too bad on my very first post.

Tough to answer this accurately,

This is a "block with a stroked crank" not much else from your 650 would carry over, but this will bolt into most any 650 ski. This only a couple key components of a higher HP motor. Unfortunately not a good fit for a newbie IMO

 

[way2manyhobbies2keep]

bump for old school cool parts

 

[Josh Watson]

bump for old school cool parts

Did this happen to come with any type of cylinder!

 

[way2manyhobbies2keep]

Did this happen to come with any type of cylinder!

a couple, no diea if they are matched, supposedly my riva cyl was the match,

 

[Josh Watson]

a couple, no diea if they are matched, supposedly my riva cyl was the match,

Dang, I’d like to get it and build something but have no idea how the stroker crank would effect port timing or what spacer plate id need to run it

 

[way2manyhobbies2keep]

Dang, I’d like to get it and build something but have no idea how the stroker crank would effect port timing or what spacer plate id need to run it

For the money you are still ahead, can hardly get a crank for this price

 

[way2manyhobbies2keep]

Time to ebay this thing

 

[650sxtryhard]

Would you sell just the crank?

 

[way2manyhobbies2keep]

Would you sell just the crank?

I mean i could, i think I have a core you could have rebuilt as well