Search results

Thanks for the help guys, will do… I am now down the rabbit hole, after fogging the engine for “just in case” purposes I noticed my carbs were looking a little gunky, so I decided it’s time to rebuild them. Now that I have the carbs off and hearing about broken reeds, I’m thinking it may be...

Story.. 1. Ski sunk, friend tried to start it 4-5 times 2. I Pulled spark plugs, got all water out 3. I fired her up and ran it for 30-45 min …she runs good so far, worried about a bent rod or crank from trying to start it with water in it. How would I tell if a rod or the crank is bent?? Or...

Hey just wanted to circle back and thank you guys for all the info. Just had to keep the front 2 bolts snug while placing the shims, and use a breaker bar to place a little pressure on the back of the pump to slide the shims into place easier. Got her all lined up and put back together. Thanks!!

Ill give it a shot, when I first tried that I could hardly place any shims since I had to put a lot of pressure downward on the back up the pump to give enough space to place a shim, felt like it was almost bad for the pump or the mounting points for the pump. I'll give it another shot today...

Hey guys, finally got the time to rework the ski using your inputs. I got the Cold Fusion alignment tool and pump shims. I installed the alignment tool, and saw that the driveshaft needed to come up because it was sitting low. I loosened the 4 bolts on the pump, and started to install the...

Yep, I definitely remember having to pull up on the mid shaft to get the bolts to line up. Also, I just took a look at my pump and there are zero shims on the bolts, I am the second owner of the ski so.. not sure if the first owner didn't know what he was doing but it seems unlikely that zero...

Hey Guys, Thanks for all your responses, I think I have it figured out now. Being the first time replacing my mid shaft housing and hearing your feedback, there is one thing I did not do. When replacing my mid shaft, I did not think about how the driveshaft lined up with the hole in the...

Thanks for the responses guys. Jet Ski Dude, I hope this is the case, I was thinking maybe its because its a all new Midshaft and it just needs to wear in a little. Proformance1, I reshimmed the engine as straight as I could. I ran the ski for 5ish min, I did rev it a few times to make sure...

Quinc, Hopefully im tracking your question correctly. I never took the driveshaft out, I just replaced the Midshaft housing, I didn't think I needed to lineup the driveshaft if I am just replacing the Midshaft... Am I wrong on this? Nick

Hey guys, So I installed my new Midshaft housing with new bearings and seals all packed well with marine grease. Put the engine back in, lined it up and got the ski back together. Started the ski (on the trailer connected to the hose), no major vibrations and engine runs good, but when I went...

Sorry for the delay, and thanks for all the info! Pulled the engine today, all the engine mounts were broke and in bad shape. Excited about getting the new rhaas mounts in. Anyways, the problem I ran into today was trying to get the midshaft housing unstuck from the hull? It looks like the...

Keeping this short guys. Pulling my engine to replace the 4 motor mounts I broke. I plan on keeping the carb and exhaust in the hull to minimize wiring/tube disconnect. The only 2 gaskets i need are the intake and exhaust, correct? Anyone recommend on pulling the carb and exhaust out with the...

Ok thanks guys for all the help. Replaced the relay and that fixed it, now I just need to put everything back together!

Hey guys! Took all your advise and was able to get an OEM relay and gasket from Jetmaniac for a good price. I will install the new parts tomorrow after work, and I will let you guys know if that does the trick. Since I was able to get both relays, I took some pictures for anyone who is...

I bought this one off amazon, I know it’s a knock off but it had pretty good reviews and, it’s only a relay. Starter Relay Compatible with Yamaha Stroke 225CC HPDI 250CC OEM# 68V-8194A-00/ 68N-81940-00-00/ 68N-81940-00 https://www.amazon.com/dp/B00MWBCKSA/ref=cm_sw_r_cp_api_i_TX4ZCb90SHBM5

Thanks for the help guys! Here is a update 1. Narrowed it down to the relay, there is 12 volts going to one side of the relay and 0 going to the other when the start button is pressed. I jumped the relay, and the starter turns. I also tested the switch by connecting the voltmeter to the plug...

Ok guys, First thanks for all the suggestions! This is what I accomplished today. 1. Tested the resistance between the positive and negative cables where they would connect to the battery. I got some resistance. 2. Checked the fuse, it is in good condition and I even tested the resistance...

Thanks 2lick, Here are some more details. The bilge was wired to the battery, but i ripped it out because i am putting in a new one at a later date. I also disconnected all the wires that went to the bilge. I just checked the new battery, good juice. W The battery cables look good, points...

Hey guys, going to keep this short and simple. Ski worked last week. Took out my bilge because I am going to install a new one later this summer. Removed it, caped the wires, and disconnected them from battery. Went to start, nothing, not a sound. Plain nothing. Installed new battery (needed...

Thanks guys! I feel much more at ease, I always flush with Salt Away after every time I ride, so I think everything will be okay. I will post an update once I figure out what's wrong with the ski. Hopefully nothing major, and I think I am going to rebuild the carbs while she is down... can't...