- Location
- CT
Do on a SN you need to run a RN waterbox.
Finally An Aftermarket SJ Exhaust Hose! From Rad Dudes
- Thread starter Twinturbostang
- Start date
CD155MX
Squirrel!!!
- Location
- Alta Loma, CA
You may want to ad that info to your initial post and website if its not already there.
I have some extra piping and couplers lying around. I'll probably rig something up for my GF's ski to run the stock SN box.
CD155MX
Squirrel!!!
- Location
- Alta Loma, CA
Matt has a point.
I'll see what I can to with the pile of left over silicone pieces and piping that I have from past projects to make it work. If I don't have the right stuff lying around I'll just purchase a transition piece. Gotta make the GF's ski pretty. haha.
h2odesperado
Pin it to win it
- Location
- Charlotte, NC
I'm running one of these in a RN with a square waterbox. Fits well, not a lot of overlap on the waterbox end. Hell of a lot better than my aluminum tube setup, looking forward to see how it holds up to my super dry exhaust.
CD155MX
Squirrel!!!
- Location
- Alta Loma, CA
Ok so last night I ghetto rigged a solution to make the Rad Dudes Exhaust work on a stock SN with a stock SN waterbox.
The Rad dudes exhaust is too short and the wrong ID (2.5" instead of 2") to connect to the back of the engine compartment at the bulkhead. I used some extra pieces I had lying around from past projects. I probably should have bought a transition coupler, but this is going on my girlfriends ski, just to make it "pretty" and the ski doesn't usually see a lot of airtime.
I took a piece of left over 2" OD exhaust piping ~6" long and used two 2" ID silicone couplers. I used one coupler to connect my 6" piece of exhaust piping to the exhaust piping at the bulkhead. I put the other 2" coupler over the other end of the 6" piece of piping and made it flush with the end, thus making the OD at that end close to 2.5". This end slid snugly (is that a word?) into the end of the Rad Dudes Exhaust Tube (with a little windex to help slide it in) and I clamped it all together with the supplied T-bolt hose clamp. The setup is pretty sturdy and isn't going anywhere.
Hope this helps anybody concerned about ordering one for a stock SN ski. You just need a couple extra pieces and you're good to go.
The Rad dudes exhaust is too short and the wrong ID (2.5" instead of 2") to connect to the back of the engine compartment at the bulkhead. I used some extra pieces I had lying around from past projects. I probably should have bought a transition coupler, but this is going on my girlfriends ski, just to make it "pretty" and the ski doesn't usually see a lot of airtime.
I took a piece of left over 2" OD exhaust piping ~6" long and used two 2" ID silicone couplers. I used one coupler to connect my 6" piece of exhaust piping to the exhaust piping at the bulkhead. I put the other 2" coupler over the other end of the 6" piece of piping and made it flush with the end, thus making the OD at that end close to 2.5". This end slid snugly (is that a word?) into the end of the Rad Dudes Exhaust Tube (with a little windex to help slide it in) and I clamped it all together with the supplied T-bolt hose clamp. The setup is pretty sturdy and isn't going anywhere.
Hope this helps anybody concerned about ordering one for a stock SN ski. You just need a couple extra pieces and you're good to go.
Last edited:
- Location
- CT
So I never thought it would happen, but we ran out of Black. We still have red, green, blue, and purple all in stock ready to ship.
Going to be 6 weeks or so or black. But lack is boring, buy a color and spice up that engine bay!
Going to be 6 weeks or so or black. But lack is boring, buy a color and spice up that engine bay!
Are the SN hose longer or the same to RN hose?
- Location
- CT
SN hose is a smaller size hose. Its 2inch
The Rad Dudes hose is closer to 2 3/8
The Rad Dudes hose is closer to 2 3/8
CD155MX
Squirrel!!!
- Location
- Alta Loma, CA
The pictures I posted for comparison were a Rad Dudes hose vs. an OEM Square Nose Hose.
The Rad Dudes hose should be the same as a Round Nose Hose.
- Location
- CT
Yes it's the same size as the RN
- Location
- amarillo ,tx
How long r these
- Location
- CT
- Location
- CT
Red and Black will be back in stock in 2 weeks.
- Location
- CT
The container from Japan should be here this week. So all colors will be back in stock soon.
FL-cracker
X-H2O
- Location
- old exit 72 Melbourne
Is black or red back in stock? I sent a email and pm about a blaster rear exhaust question too.
Thanks
Bronson
Thanks
Bronson
- Location
- CT
They are so close. Guess they are on a 8-10 hold in customs. So I'm hoping to get them Friday.
FL-cracker
X-H2O
- Location
- old exit 72 Melbourne
Thanks man, just bit the bullet and ordered a purple yesterday.
- Location
- crystal lake
Why wouldn't you have this info on your website?? I would have never ordered this $100 useless hose. Will you pay for return shipping?