Other Length difference between Limited and Mod chamber?

[OCD Solutions]

I am pretty sure I know the answer but can't find it posted anywhere.

Is there an actual overall length difference between the SJ Mod and Limited chambers or is the difference in the fat section of the pipe where it fits around the gas tank?

What are the chances someone has both that they can snap a pic and take some measurements for me?

 

[RyanO]

[url]http://factorypipe.com/p_yamaha.php[/url]

 

[RyanO]

You can see the cut mark where factory pipe removed 1.5" from the limited to make this pipe a mod.

 

[TheBuzzard]

the mod pipe clears the gas tank more than the limited. not all have the weld but when you open the hood, it takes one second to tell a mod from a limited. the limited is pretty close to the tank and the mod aint.

 

[OCD Solutions]

Tanks not the issue...Just want to be sure of a couple facts before I make a recommendation on a solution.

 

[TheBuzzard]

not even the mod pipe is going to connect to that waterbox.

 

[BruceSki]

Just weld them together!!

 

[speedysprocket]

I had to cut about 3/8" off the end of my pipe and shorten and change the angle of the inlet to my H2O water box to get them to fit in my Foot Rocket.

 

[OCD Solutions]

Is the H2O waterbox just too tall to get the breather tubes routed above? If the tubes were higher then the box could go almost 3 inches further into the nose of the ski.

I still say the ATP waterbox is the by far the best choice for these shortened and rocker skis. It's small and round and can be rolled to fit damn near any ski without any modification.

 

[MikeyB]

Yea the inlet of the H20 designs box is wack..


Sent from my iPhone using Tapatalk

 

[IS0LD0UT]

Was wondering the same thing. Which is this mod or limited. I was going to pull it to compare to a limited.

 

[BruceSki]

http://www.x-h2o.com/index.php?threads/factory-pipe-is-this-a-mod-or-limited-setup.126208/

http://www.x-h2o.com/index.php?threads/factory-pipe-is-this-a-mod-or-limited-setup.126208/

 

[IS0LD0UT]

http://www.x-h2o.com/index.php?threads/factory-pipe-is-this-a-mod-or-limited-setup.126208/

Linky no worky

 

[OCD Solutions]

The highlights;

The pipe measures as following:

• Total Length: 25 3/4''
• Circumference: 16 3/4 ''
• Diameter: roughly 5''

Specs found here on the X:

• Total Length:
  • Mod Pipe = 25-1/2"
  • Limited Pipe = 26-1/2"

 

[IS0LD0UT]

Think my picture is a mod its roughly an inch shorter big coupler to water fitting.

 

[Idok]

either 1 or 1.5"

 

[DAG]

Just cut the box inlet, no big deal. Took me 15minutes to shap to fit in a rocker SN. But yeah, i bet the next batch they make will be more legit, they know of the issue.

 

[speedysprocket]

So is the Octane chamber even shorter than the mod...? I just got a rough measurement on mine while in the ski at about 24 1/2" to 25" long.

 

[keno]

I'll measure my octane chamber this weekend to verify. I always thought it was in between the limited and mod.

Sent from my SCH-I545 using Tapatalk

 

[speedysprocket]

Mine appears to be even shorter than the mod. I'll have a new mod chamber in a few days though and can compare them.