SX/SXi/SXi Pro New Sxi Pro Owner

[sxipro02]

3500 for mine 4 years ago but it was minty and on a trailer.

 

[sxi steve]

$2600 in 2006 (with no trailer).

Totally stock, like new condition, bottom was near flawless.

From an older family man, he had a couple coucher too, didn't ride his Pro much.

 

[Brick-SXi]

Okay /// back on topic

Managed to get some work done this weekend with working some OT saturday


Found some heater hose that fit the bilge outlet - this will give me a nice bend to prevent water coming back in and shield from the WB heat ( still need some hose clamps)

Added a new pole pad and the latch hardware

Wired the bilge switch and re-did all the electrical connections

Also mounted the start stop / bilge switch

Does anyone have a set of upper and lower pads laying around ? I really need a set in good condition

 

[PWCSAR]

Here's a set of bar pads for sale (not mine) I'd just give them to ya.. Don't know if ya want to spend this much, but here's a set.. J.

http://www.pwctoday.com/showthread.php?t=381259

Searchin for a few parts I am lookin for, I just saw these
a little cheaper.. http://www.pwctoday.com/showthread.php?t=384115

 

[TontoM3]

this makes me think I did a crappy job on mine now. but then again. I did a crappy job. I guess this re motivates me, time to strip everything down......

 

[kkwedell]

I'm sure you did fine. :biggthumpup:

 

[kkwedell]

What's happening with this build?

 

[Brick-SXi]

What's happening with this build?

Hurricane Sandy has forced this builder into 80+ hour telecom worker weeks

Hope to finish it all up soon

 

[kkwedell]

Well, it's turned out great so far

 

[Brick-SXi]

Well, it's turned out great so far

Thank you - I will get back on it soon

 

[jim_ii]

Good work so far! It's only Nov and I'm ready for spring already!

 

[Brick-SXi]

OK Gurus - what is the secret to keeping this bumper seated - every time the handpole goes up it unseats the new bumper

 

[kkwedell]

I just use a limiting rope, and don't worry about the bumper

 

[Gyro]

Mine does the same thing.
Haven't done anything about it yet but have been thinking I could put some kind of silicone between it and the alloy and then stuff the space between the bumper and the pole with paper towel/rags to hold it in place while the glue sets.
One day I'll get around to it.

 

[Brick-SXi]

Rainy winter day progress

Before - uke:

After - :Banane57:

Finished the bilge hose and wiring, dropped the motor in and got it somewhat aligned, re-did the main cooling in line , also installed a fuel filter

 

[SP33]

Ski looks clean!

 

[kkwedell]

Lookin good, gotta get a pipe for that braaap!

 

[Brick-SXi]

Lookin good, gotta get a pipe for that braaap!

Want to keep this ski stock and reliable - the Seadoo behind it has a "little work" done to it 16lbs of boost FTW

 

[hornedogg79]

Want to keep this ski stock and reliable - the Seadoo behind it has a "little work" done to it 16lbs of boost FTW

Lol..... you used "seadoo" and "ftw" in the same sentence.

 

[Brick-SXi]

lol..... You used "seadoo" and "ftw" in the same sentence.

ftmfw -