SX/SXi/SXi Pro New Sxi Pro Owner

[Brick-SXi]

Motor is aligned - bed torqued to the mounts

Installed the drives-haft coupler cover , trimmed the exhaust coupler to fit the TDR box , clamped up the main cooling line

Also added some braided covering to the battery cables , really like this stuff vs. flex-loom; may have to re-do it

 

[kkwedell]

Looking good

 

[kawi kid]

where did you get the new tank foam?!

 

[Brick-SXi]

where did you get the new tank foam?!

I got mine here

http://www.kawasakipartshouse.com/o...1e940/1998-jet-ski-750-sxi-pro-js750-c1-parts

might want to check if there is a forum sponsor


You can try cycle parts nation too , may be cheaper -

 

[TontoM3]

you were the one that gave me inspiration to revamp mine, and it was a lot of work but darn it feels good to own something that clean! here is a few of mine


thanks for the motivation! haha

 

[kawi kid]

I got mine here

http://www.kawasakipartshouse.com/o...1e940/1998-jet-ski-750-sxi-pro-js750-c1-parts

might want to check if there is a forum sponsor


You can try cycle parts nation too , may be cheaper -

Awesome, thanks for the info! I get dealer cost on everything but i didnt know Kawi was still making them

 

[Brick-SXi]

Awesome, thanks for the info! I get dealer cost on everything but i didnt know Kawi was still making them

Here is the PN

16031
FLOAT,FUEL TANK
16031-3846

$55.43

 

[Brick-SXi]

Hello -

back from the dead and ready to hit the water!

I put acid in the battery and charged it all up. What procedure should I follow to start the ski for the first time?

I have fresh fuel ready to go

 

[TontoM3]

It's been a while! I rarely get in the x because my tapatalk doesn't push notifications. But if its a fresh top end, the general rules are 32:1 oil to gas let it idle first tank of gas font got above half throttle with small intervals of 2/3 throttle and 3/4. Check plugs for correct brown color.
Next tank vary your intervals to wot and 1/2 to 2/3. Never pin the throttle. Make sure your getting sufficient cooling and listen/feel for any vibration.

 

[Brick-SXi]

It's Alive !

 

[Brick-SXi]

Not bad for my first time turfing and using contact cement ! My Dad and I knocked it out !

Rails tomorrow; any tips?

 

[Brick-SXi]

Spent a few hours on the rails and rear today. Got the factory kick plate and new tie down eye installed. Rails are a PITA

 

[Brick-SXi]

Finishing the nose this and hope to finally ride this weekend

 

[Brick-SXi]

A little closer each night after work. Hoping to take out this Sunday

 

[TontoM3]

That is some serious clamping. But man is this ski going to rock! Wish I was closer to come ride

 

[Brick-SXi]

That is some serious clamping. But man is this ski going to rock! Wish I was closer to come ride

thanks ! Didn't want the turf lifting. Been so humid in Nj hard for this stuff to dry

 

[Brick-SXi]

Two years of sporadic work condensed into 2 minutes

 

[TontoM3]

That was a jive-a$$ video man! Now just learn how to rip on that thing and every other ski besides a 550 will be pretty easy to ride.

 

[Brick-SXi]

I need tons of practice Planning on riding all day Sunday !

 

[TontoM3]

Hey how'd the ski run the rest of the season? Do you enjoy it?