Custom/Hybrid Okie XFS 771 Build

badvinny

badvinny

Location
Saskatoon,SK
My dive style boots were slippery with the RRP turf, but 2 other sets of wet shoes I use are excellent on thier turf, of course it is cheaper and easier to get new shoes!
 
Last edited:
JetManiac

JetManiac

Stoked
Site Supporter
Vendor Account
Location
orlando
Looking good, Austin! Like the pics sitting inside the bare hull.

Make sure to sand paint off of the 2 grounding bosses in the ebox before reassembly.
 
Yami-Rider

Yami-Rider

TigerCraft FV-PRO
Location
Texoma
slamb33 said:
what kind of mods? can you share any?
Click to expand...

Sorry, but they are super secret and can not be shared..lol


Ya i can get some photos up later.


kieran79 said:
Dose the pump shoe have the 4 screw holes already there or do you line the pump shoe up then screw into fiber glass
Click to expand...

There is 4 little pilot holes pre-drilled for the pump shoe. you may have to enlarge to screw holes depending on what size SS screw you use.


jetmaniac said:
Looking good, Austin! Like the pics sitting inside the bare hull.

Make sure to sand paint off of the 2 grounding bosses in the ebox before reassembly.
Click to expand...

Thanks, will do.
 
Yami-Rider

Yami-Rider

TigerCraft FV-PRO
Location
Texoma
slamb33 said:
what kind of mods? can you share any?
Click to expand...

Here are the few mods i have had to do so far to make things fit correctly.

Grind off the bottoms of the hood prong nut plates.

IMG_2625.jpg


Flatten or cut off the angled alignment base on the rubber strap holders for the WB and fuel tank.

106_0136.jpg


Shorten the hood latch base so the latch will close.

IMG_2627.jpg


Thats basically it so far.
 
Last edited:
Yami-Rider

Yami-Rider

TigerCraft FV-PRO
Location
Texoma
Re-installed pump assembly with cooling lines, hooked up the trim cable and blocked off the suction bilge.

106_0142.jpg


Homemade trim cable rubber seal. Piece of 1/2" hose with a piece of 5/16 hose inside of it.

Before:
106_0121.jpg


After:
106_0125.jpg
 
Last edited:
Crab

Crab

thanks darin...noswad!
Location
Seattle
I like the building process...also wondering if the prop is correct for that setup as I run the 9/15 hook with the same pump and stock bore raider trim nozzle. A 10/16 hooker is alot more prop than the 9/15 IMO.
 
Last edited:
Yami-Rider

Yami-Rider

TigerCraft FV-PRO
Location
Texoma
kieran79 said:
Update
Click to expand...

I will get some pictures up soon. The motor mounts and mid-shaft housing have been on back order from Rhaas, so I haven't been able to do much, I'm suppose to receive them this week.

FearMyWrX said:
Looks fricken awesome man!
Click to expand...

Thanks!

crab said:
I like the building process...also wondering if the prop is correct for that setup as I run the 9/15 hook with the same pump and stock bore raider trim nozzle. A 10/16 hooker is alot more prop than the 9/15 IMO.
Click to expand...

For my freestyle setup I was told to run the 11/17 by two well know engine builders.
 
Yami-Rider

Yami-Rider

TigerCraft FV-PRO
Location
Texoma
I got the motor mounts in today! Installed mounts, fuel tank bracket and mid-shaft spacer plate.

Homemade fuel tank bracket...I think it turned out nice.:Banane25:

IMG_2629.jpg


Installed

IMG_2647.jpg


Went with the couch mounts :naughty:.

IMG_2632.jpg


Bottom

IMG_2635.jpg


Installed

IMG_2642.jpg
 
T

Texan33

Yacht Wakes Hunter
Location
Texas
Yami-Rider said:
We're hoping to. Alan and Tyler are going to buy wetsuits. I already have one and have still been riding texoma when the wind picks up.
Click to expand...

Hit me up soon. I'm getting another ski in a few days that will replace my sxr so I'll be riding soon.
 
Last edited:
slamb33

slamb33

s
Location
NorCal
Nice work. I love seeing updates on this thread.

How did you make the fuel tank bracket, and how did you fasten it to the hull? Are you running a stock SJ tank?
 
You must log in or register to reply here.
Top Bottom