Super Jet Please do your part to protect the future of the B pipe.

[yamanube]

And grind your bedplates down so they don't rub holes in the chamber.

I have been seeing a lot of B pipes for sale with rub marks nearly through the chamber, yes, yours might not rub, yes it can be welded, but why not take 5 minutes and knock the corners off your bedplates. If not for you, for the next guy.

Picture stolen from Blake, lower right of the image is the area to be ground.

 

[Big Kahuna]

Lol

 

[b.lee]

... I wish I could afford a b-pipe, lol

 

[MADMAT]

Just happened this week in our crew.....

 

[Vumad]

Limited or mod? My limited wasn't rubbing there I don't think, but I just got a mod. My destroyer bolt did take a nice chunk out of my limited though. Left backmost bolt needs like 3/4" cut off of it.

 

[SJ 701X]

Or you could just put a dent in the chamber where it happens.

 

[MADMAT]

Our guy had a mod in a stunt hull....I think....

 

[KTM434]

Or you could just put a dent in the chamber where it happens.

I'd rather grind the bed plate down for clearance than dent a chamber.

 

[Tyrant1919]

Grinded mine down after it happened. Still happened a little bit more. Probably because I never checked it. Meh.

 

[Half flip95]

but if you keep all the existing b pipes in good condition, then they won't sell any new ones and factory pipe will stop making them. then they will cost 9000.00.
The future sucks!

 

[zzylstra]

Never had mine hit on the bedplate. Previous owner did let it bang on there for awhile. I've got a good inch between the two with my xscream waterbox

 

[OCD Solutions]

I bought a carbon B-pipe off Yamanube a few years back and he told me about this mod at the time. I checked the other B-pipe I had purchased new a few months earlier and found it was rubbing there as well.

Now I trim all my bed plates just to be sure. Only takes a few minutes and could save you some money and a day of riding.

 

[Matt_E]

Or you could just put a dent in the chamber where it happens.

So the options are:

1. Put a dent into the carefully designed, tuned $400 chamber
2. Spend 10 minutes to grind down a corner on a $7 bed plate.

Ima hafta think about that one, I'll get back to ya'll.

 

[oside-tanner]

I'll second the fact that if you install destroyer tubbies, make sure you grind the bolts that end up behind the chamber, It felt like a high frequency vibration while the chamber and destroyer bolt were hitting each other

 

[yamanube]

I bought a carbon B-pipe off Yamanube a few years back and he told me about this mod at the time. I checked the other B-pipe I had purchased new a few months earlier and found it was rubbing there as well.

Now I trim all my bed plates just to be sure. Only takes a few minutes and could save you some money and a day of riding.

You wanna sell that thing yet?

 

[OCD Solutions]

You wanna sell that thing yet?

LOL, nope. :biggrin:

 

[feartheride]

So the options are:

1. Put a dent into the carefully designed, tuned $400 chamber
2. Spend 10 minutes to grind down a corner on a $7 bed plate.

Ima hafta think about that one, I'll get back to ya'll.

bed plate is 92.95 , just saying oke:

 

[yamanube]

Show me somebody who has payed $90 for bedplates, just saying.

Better yet, show me somebody who is willing to pay $90 for bedplates!

 

[txsuperjetfreak96]

X2 maybe from yamaha, aint know body got time for that


Jeremy

 

[Matt_E]

bed plate is 92.95 , just saying oke:

LOL you got ked if you paid that.