Search results

The first 144mm trim i bought black one in pics had them orientated that way. I copied that. Parts will come today i will mock it up see if it better reverse

Ok i will mock it up and try

Got high strength permanent thread locker in pic. Previously used the blue medium strength in pic. Hopefully this solves it then

I used blue thread locker. It had been sitting in the garage for 20 years. Didnt think it would expire but maybe it wasnt strong enough. I will get the high strength thread locker red next time once my parts arrive. I clean my threads. I did leave it over 24hours before use but it still came...

I recently took my steering nozzle off of my trim as i need to access my pump. I screwed it back on with the bushings and bolts. I ran it on the trailer and the bolts came loose. I then put thread locker on the bolts and ran it on the trailer and it was fine. On my first run in the water the...

I have a stator pulser coil that when it heats up after running for about 10minutes it fails working. So i want to replace it. It is on a 62x stator and my flywheel is lightened. Can a 62t and a 61x pulser coil interchanged ? I wanna buy an old stator probably rusty but it might be a 62t and...

The bellows on my powervalves are coming off the top round cap from time to time. They normally held on with a circular spring to the cap. I have been trying cable ties out now as they are stronger then a spring but it happened again. Possible reasons anyone ?

poop hey prob the capacitor. I figured the brain is dead. I rewired the entire thing by splicing the wires real short and soldering on new ones with heat shrink covers. I did use the same fuse box though. It dont look corroded but hey my last shot i will chop the fuse out and see if it will at...

i kind of gave up on this. But i did get a timing light on it and cut down a flywheel cover for bendix covering only and it only lights up for the first spark when cranking starter. then now more flashes. if you let it sit for 30 secs it does the same lights up first spark. if you dont let it...

I manually checked the timing again. Found TDC on cylinder. Marked it on case. Switched to LED mode. Found cylinder set to 30deg. Checked the other cylinder it set to 30deg as well. I waiting to see if my mate has a poopty old flywheel cover to chop in half for a timing light. Not sure what...

my woodruff key is fine and the flywheel grove is as well.

yeh i tried it not long ago. It backfires even worse as it shoots flame out the exhause. I am 100% sure i got the leads right i tested again manually. Stick screwdriver down plug hole to check which cylinder is coming to TDC. Put screwdriver in lead that is connected to that cylinder and turn...

I dont have a spare cover to cut up. I will See what i can sort out. If it 60 degrees out. How ya fix that ? Anyone got an answer to my msd brain being fully waterproof question ?

OK i got a timing light. Works on my car. Last time i tried to use it on jet skis it didn't work. No idea why i will check it out. So i assume i use the light on the flywheel with its cover off. Do i look for tdc or advance on the flywheel with the light. I would normally liquid paper mark TDC...

Yeh they are not mixed up. I checked each coil fire to piston position TDC.

Update. As i mentioned i bought another MSD system but the brain was broken. The coils are good though. I know this using the same tests i used above. So i put the second set of coild in use and i get the same backfire as in the video i submitted. So i dont think it is a coil issue. Is the...

I have a MSD total loss. It was in a functioning ski and was working fine. I rebuilt the motor and put it back in and it is not running. So i put stock ignition on to the motor and it runs fine. So the motor is fine. So i have pulled the motor and ignition out of the ski. I have rewired all...

no tie down hooks in bed at the bottom of tub only on the top in each corner. i wanted to to put skids in with a winch at front of tub so i could add a ramp to winch up the ski on to bed / rails. therefore not needing a trailer. i dont always have someone with me to lift the ski straight onto...

Ok i will clarify. I want to put rails of wood or aluminium in truck tub (tray) to hold ski. The tub is too short so the tail gate needs to be down when i put rails in. I dont want to drill through tub /tray base to bolt the rails (skids) to the tub base. Has anyone got a way to secure...

Wanting to make jet ski skids for a trub tub to hold jet ski in it. Its a short tub so tray need to be down. Or i need to make it sit on top of tray ledge. My question is i dont want to drill into the tub to mount the jet ski skids to to tub via bolts. Anyone got a solution they have used to...