Search results

LOL is turfing EVER fun? Footholds got done yesterday so Saturday ride is on. I have opted to wait until after the freeride to shorten the pole. Because of the resin cure time.

OK. Done. Less is more. :)

My registration ppwrk showed up today! Halleluja! I had the temp papers but there were no numbers at all so it would mean possibly getting pulled over every shift change!:eek: But no more! :D

True. But I have already cut the hull so it is being done now. I wont be able to leave for NC until after work tomorrow anyway so I get bonus cure hours beyond 24.

This weekend is getting to be maddening. lol I gotta get my crap together. If anyone is interested I have a great smoker I would be willing to bring and smoke ribs in. I can get about 20 racks in there. It takes 7 hours you pretty much set it and forget it so I wont miss out on any skiing. If...

Thanks. Great advice. I only use epoxy. Ya, the cure time will not be my friend. I am comfortable doing the work. I needed to get a solid plan of attack. It was my intent to seal the foam behind the gunnel with its own layer of glass to try to avoid water admission in case a foothold micro...

So I started looking closely at the footholds :( My sneakered foot is a tight fit. The glass in the foothold flexes 3/8" when I stick my foot in there. I cant imagine how my foot will fit in there with padding top and bottom. :( I also found in the corners there are a few holes. I didn't...

Yes!!

@Bryan.wells Here you can see how much I cut off of the new spring. The spring shown is the 2014 OEM part. I tried to show spacing for the cutting wheel kerf. I cut a little at a time to get the fit. Here is the new installed part. I lifted the pole to snap this pic and as you can see the...

The real issue is the epoxy cure time. Going to have to get the heat lamps out.

more done today. One handed is getting better. Looking good for the weekend. I might be turfing on the damn beach. :) Clean start The sob is on there... Dash off and the factory 5mil pads off. This sucked one handed but meh. Not too awful. Getting ready to play hell. Slow...

@Bryan the pole spring is the shiat! My back would hurt after an hour before. Now its cool after 3 hours!! It mostly just stays where I put it on the trailer. For the 2014 I had to take nearly 1.5 inches off the long side before it would seat properly. I will post pics of that tomorrow.

Mikesee myksee/ noun a mythical, cave-dwelling being depicted in folklore as either a giant or a dwarf, typically having a very ugly appearance. synonyms: goblin, hobgoblin, gnome, halfling, demon, monster, bugaboo, ogre

Frankly, make this image your screen desktop wallpaper leave it there for a month. After a month tell us were you bought your SJ from. even trolls gotta like that...

Everyone who is saying they are not 4 stroke is 100% right. I stepped on my dick there. </embarrassed> I guess I was under the influence of this thread in particular.

OK. I managed to stay outta this one but you pulled me in here. Dude, I feel you haven't made up your own mind about what you want. Try a 3D. I have two of them. They re stand up couches. NOT 4 strokes. Heavy. You MUST get the red one because it has the 971 in it @130HP the yellow one has a...

Do you think this is more about the plate than the nozzle?

My turf progress today was less than optimal. I did bring out the wire wheel on the die grinder and it does seem to be a good solution its just slow going and you have to mind the hull. The glue is 10X as hard as the glass. Again all of this is just the rubber caps. One is fully removed and the...

Possible Worn out plug wires. Heat raises resistance. Worn out wires makes a worn out coil...

About that bow eye question. Are folks adding an actual bow eye to the front of he hull or just adding a loop to the factory eye?