- Location
- sask, canada
Rhaas make custom mounts that are a few mm shorter than stock.
Custom/Hybrid EME Q8/Aerial 8/Micro/Roid discussion thread
- Thread starter N3vrSat1sfied
- Start date
SpaceCowboy
breaking something
- Location
- Ypsilanti Michigan
I have some if anyone wants some
- Location
- Ontario, Canada
You had them in a Q8 with Yami motor? And what do you want for them
How much?
SpaceCowboy
breaking something
- Location
- Ypsilanti Michigan
Make me an offer!
- Location
- Snowmass, CO
Im looking for some help getting a 701 mated to a yami 144 in a micro. My midshaft is definitely too long and I have not been able to get a hold of eric to see if he has a shorter midshaft. What are you guys doing to solve this?
N3vrSat1sfied
Military Member
- Location
- Fort Worth, TX
- Location
- Denver Colorado
I run cold fusion mounts with the back of the pump shimmed a 1/8of a inch. alignment is perfect! In a earlier post it sounds like you need fx1 mid shaft.
- Location
- Fort Mohave, AZ
Sooo, since I've been through this issue: EME sends a fx1 shaft, then requires you to have couplers machined down to fit, kinda crappy.
What I discovered...
To get yami stuff to work with the micro:
-gp760 midshaft (Shortest yami shaft. Get it from jetmaniac, he has the ones with the correct spline location.)
-ADA Kawasaki 1100 conversation coupler for the midshaft side, it fits the yami shaft. Same thread.
-ADA Yamaha crank side coupler
-Damper for couplers
-Several cases of beer and lots of cuss words
-In extreme cases the title for your ski, so once your really tired of screwing with the micro you can sell it and buy a superjet, see avatar pic
What I discovered...
To get yami stuff to work with the micro:
-gp760 midshaft (Shortest yami shaft. Get it from jetmaniac, he has the ones with the correct spline location.)
-ADA Kawasaki 1100 conversation coupler for the midshaft side, it fits the yami shaft. Same thread.
-ADA Yamaha crank side coupler
-Damper for couplers
-Several cases of beer and lots of cuss words
-In extreme cases the title for your ski, so once your really tired of screwing with the micro you can sell it and buy a superjet, see avatar pic
Last edited:
- Location
- Snowmass, CO
Thanks Matt, Im working on assembling superhonda's parts list. Hopefully Ill be back on the water soon!
- Location
- Fort Mohave, AZ
Should also mention I had to run shorter rhaas motor mounts, with stock mounts the engine sat 1/4" too high. Alignment was impossible.
- Location
- Ontario, Canada
I just bought 3/8" shorter motor mounts and almost aligns perfect
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
N3vrSat1sfied
Military Member
- Location
- Fort Worth, TX
Used regular sj mounts in all 3 I built
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
- Location
- lake orion MI
I used regular mounts in my Micro, but i did have to machine the couplers down about a inch in total between both of them.
- Location
- Snowmass, CO
Sooo, since I've been through this issue: EME sends a fx1 shaft, then requires you to have couplers machined down to fit, kinda crappy.
What I discovered...
To get yami stuff to work with the micro:
-gp760 midshaft (Shortest yami shaft. Get it from jetmaniac, he has the ones with the correct spline location.)
-ADA Kawasaki 1100 conversation coupler for the midshaft side, it fits the yami shaft. Same thread.
-ADA Yamaha crank side coupler
-Damper for couplers
-Several cases of beer and lots of cuss words
-In extreme cases the title for your ski, so once your really tired of screwing with the micro you can sell it and buy a superjet, see avatar pic
This worked perfectly for me. With minor modifications to oem superjet mounts I was able to get the engine aligned.
Does anyone have a micro ride plate for sale? Mines getting pretty banged up and I've been unsuccessful getting at any response for eme for the last month or two
- Location
- Fort Mohave, AZ
You can sand cast and aluminum one. Mock one up out of foam, then lay it in a wet sand box, gently cover it with wet sand, leave a few openings, to pour in molten aluminum. Works well, albeit a little time consuming. You use old beer cans for the aluminum. Several videos on YouTube to help you out.
- Location
- Lake Hopatcong
How have you been trying to contact EME?
- Location
- Snowmass, CO
I've filled out the online form a couple of times and left a couple of voicemails.
- Location
- Lake Hopatcong
- Location
- Lake Hopatcong
first freestyle ski... eme micro 701. 10 weeks of riding and I landed my first backflip. Working on flat water next.