Search results

My calipers on my 95 square say 4.625"

Motor is put together and running. Initial cold and oiled compression was 180 stator/190 pto psi. After first start to blow out the excess oil was 175/180. Keep in mind I'm using the same used pistons and rings as before, probably 200+ gallons but still looking good. I want to dial in the...

Lots of good news today. I trenched another 0.035", so about 0.055" total. that gave the bigger conrods just over 0.020" of clearance. For a reference, I checked the thickness of the case at the bottom of the valley and it was 0.118" thick. I dry fit the bottom end with both base gaskets...

Big day today. I got the crank back from Crankworks and attempted to drop it in the case. In a previous discussion with Crankworks, he told me the hotrods connecting rod big end was a bit bigger than standard. They offer a service to bring the size down and finish with a shotpeen. The rough...

Emailed Crankworks 3 weeks ago to see how it was going. Says its ready for assembly but they've been shorthanded. Hoping to get it in my hands soon. I was going to go with extended cylinder studs because of running the spacer. There's some quality control issues being worked out on those so...

One way or another that oring needs to be sealed by the rubber gasket. My sbn44's were also put together with the wrong gasket like yours and I battled an inconsistent fueling issue until i pulled the fuel pumps apart and found the problem. It would suck enough air through that gap at high...

I got my xtreme 2 on cyber monday last year for $160 shipped. Excellent sound quality and loudness for a good sized shop. Being waterproof is nice for camping and keeping dust/dirt out too.

I believe you're right. I could accomplish the same thing by just setting the first point to an rpm below cranking speed. Reading the manual again states: When "[+] and [-] signal" is checked, then both signals are detected. Revs of first ignition point define switching point between...

Although I didn't change the static timing, I also changed to + only mode and lowered the 0-500 cranking to 10 degrees. I would like to put an amp meter on the starting system and see how much easier it is to crank. By sound/feel alone it seems better.

pm sent

Bump, lowered price. Ships same day as payment received.

I thought my hull's threaded holes were off, good to know it was their product that was off. It took about 7 weeks and multiple messages to get my battery box. 3 weeks of that was because it was sent out for anodizing. Also was offered extra parts and eventually a partial refund for the wait...

After having experience with some stock superjet and aftermarket hulls, I'm less concerned with the visual hull design and more on how the engine mounts, bulkhead, batterybox, etc are mounted and secured. I don't want to buy a new hull and after a year have to repair joints and mounts that were...

I'm able to close this chapter. I sent another email on Jan 12th, as I never received mounts that were shipped on december 26th. He couldn't find the shipping record so sent it out with tracking on jan 13th and I received them on jan 18th. First email was sent October 1st...If anyone wants a...

New mounts sold. Four used mounts are sold.

The warranty is still in the FAQ, 3 years from purchase. "Do you have a warranty? Yes, Rhaas motor mounts are all covered by our 3 year replacement warranty. If they break we will replace them. No questions asked. We offer a limited 1 year warranty for commercial applications."

Waited 7 months until there was enough snow for my snowbike prototype testing. Predator 212cc, 21mph top speed and enough torque to pull two adults in a sled.

I checked my older pdcs-o2t and it draws 2 ma at idle. I've also checked the current pdcs-ao2t and it would jump to 20 ma then drop to 2 ma. It was the original zeel that would consistently draw around 90 ma and drain batteries.

If you have the programming cable you can narrow down the issue to either the cdi, stator side, or coil/wires side.

If you're like me and would rather not spend $250 on real RRP carbon tubes, Purchase the finest carbon fiber vinyl and use this 3d printed cutting template to give a seamless transition from tube to the clamping ends. The bottom has a flat boss that will keep both clamping templates clocked...