Search results

I found that when you hop the ski and nail/free rev in the air, the mag pump grabs the water and hooks up a lot faster. It allows you to really get the revs up and have almost instant punch when the pump hits the water, and you don't get that cavitation that you do with a stocker. On the...

Ok, here's a new twist.... Even when it is free revved out of the water, it still won't rev past 6k. It doesn't seem to be hitting a limiter either, so I'm now thinking it could be a fuel delivery issue. The flywheel was fitted about a week ago, but as it isn't my ski, I'm unsure if there...

Yeah, leaning towards that myself. I don't think I've seen anyone running this pitch in an sxr before, but then again, this is a new Hooker prop from Impros. What should the nozzle be bored to? I also forgot it has a stubby pump cone...anodized green, I'm thinking it might be Blowsion...

Yep, I'm wondering this myself...I haven't heard any bad stuff.

Will check the water in the header pipe, but last time I adjusted it was 1/4 turn open on the bottom and the top and middle closed. I think stock rpms are around 7000 but without the top end revving its a pig to ride! I thought it may be an electrical problem, but prop pitch is the only...

Hi guys, I thought I would run this by you SXR guys in case you've seen the problem before... Setup is a stock SXR engine with wet pipe, Jetinetics flywheel, VF2 reeds and Hooker 11/17 prop...Have dual cooling from the pump with one circuit running to the head pipe and dumping overboard...

Heh, his name isn't Steve by any chance?

Awesome....! Might have to speak with you about some anodizing Brian...damn!

It's a tough call....this seems to be a hot topic at the moment here in Australia. I've ridden stock hulls for years and loved every minute of it, but I got sick of repairs all the time. I went for an XFT hull and was more than impressed with the build quality and weight. I beat on that thing...

Haha, thanks guys... yeah we do get some really good surf here, and the best part is that at most we only have to travel for 20 minutes to get to it! The helmet cam is the Gopro wide. Although not the best quality, it gives you an idea! The video was made with Adobe Premiere. I do go...

Any updates on this? How does it perform?

Hi guys, I thought I'd throw up a video of some winter riding in Portland, which is in the south of Australia. Very cold most of the time, but we get some damn good surf!

Try looking at the horizon...it seems to set the ski to rotate around you. I was having the same problems... Here's a vid we made, it might help, or not!! http://www.rpcrew.com/?page_id=15

I have one....it's nice, and weigh's 500 grams more than a stock pole!

So nobody seems to know the weight of the Titan pole. Not sure how thick the tubes are but being stainless, it would have to be double the weight of the alloy tubes of the RRP pole (assuming it's stainless exhaust tubing that's used) Weight is a big factor for me anyway....with an aftermarket...

Even when I do that, it still searches with OR between words?

Is it just me or are we only able to search on individual words? If I enter a phrase, I get an OR between each word, rather than it searching on the full phrase. This worked fine when the little drop down box appeared under the search link, but now it's gone... Any ideas?

Hi Matt....glad you got it, I was just going to send you a message to make sure! Installation time will be about 20 minutes!

Very nice! Well done. Most people either let go, or appear to come out of their footholds. Both of them are a mental thing I think. You know your feet are in there, but they still come out!

I can't recall the reason why you are unable to run higher advace down low, but I run a big bore 6mm with initial advance of 32 degrees. I haven't had any problems with either the MSD TL or the ATP flame. Every single Advent I used ended up cranking at 50d btdc and used to backfire and flame...