Search results

Contact Watcon, He still recurves the PVL Cdis.

Looks Great DBird

When did JSS stop working on Polaris stuff? I just had him do some work last year.. that sucks

http://www.jegs.com/i/JEGS Performance Products/555/10784/10002/-1 Jegs, has them 23 Bucks and free shipping- I've ordered them in the past. You get both male and female ends so that you can match both your stator output harness to your ebox harness.

Looking good! -Blue/Chris hooked my 61x cylinder last year with a xtra porting treatment and a 735 kit same as yours. Fast turnaround and great service as always. I can't wait to try it in a light hull as it's been sitting for unfired and sealed up for almost a year now! Too many projects but...

HondaBond here as well. 1211 is excellent too, Just easier to find Hondabond at my local deal close by. Also OP If your running a Girdled head, put some around all the girdle studs where they go into the cases. that way the water cant get down inside the holes and threads and cause corrosion...

Competition Creedo : You have to pay to play.. However Money does not compensate for skill, sportsmanship or downright common courtesy

-Fu*k a bunch of jetskis -Never trust a fart after 40

Very Nice! Its crazy to see such quality in a short amount of time. Good things take time.. Great things take Hink! Keep it up brother!

The swap is fairly easy and will not be a night and day difference. yes you will have better carb response with the dual setup if they are tuned right. but just putting the engine in will not be the end fix. now if a 62t bottom end is going into the fx1 you will need his electronics or have to...

@LimitedSlip7 Contact him, He made a few tanks tailored for a brawler that will also hold your battery

John Does all PWC Electrics. From connectors to stator wiring to coil refurbishing.. he will build total loss systems, refurbish and test faulty cdis and msd enhancers and if you call him up, he will go in to grate detail of any electrical woe you can think of. He does not limit his services to...

Riva has their own bracket for the red pipe. the base hexagon plate mimics that of a stock oem head and bolt holes. a stock bracket with the oem lift loop will work on the riva pipes. I have not seen a Riva pipe bolted to an ADA mount. dont go hacking up your new head, you'll have to modify the...

Those are unicorns! Good luck finding a set. As those are the only in existence! Nice work Alex

Erik ( TPE ) Built Speedys 950 polaris using a different cylinder than that of the TPE engine you now hear of and see. I believe the malone engines as well as Alex ( speedys) uses a polaris based sled cylinder and cranks. Most of that engineering and parts are sourced from a sled catered builder...

Check the diameter of the domes. That may be a 650cc 6m6 style head. a 650 protec head will run 78mm across in diameter, A 61x 701 rec head will run 82mm across in diameter. the rec heads are grooved with an provison for the Oring. Early Rec heads had one threaded mount hole near the front...

Whom I'd ask... @tom21 @Idok (f1pro veteran) @LimitedSlip7 ( he built and chopped his f1pro last year ) @Hornedogg John (f1pro) Wildcard input who always has a golden nugget of fx info.. JD-@specialfx

anyone order a carbon 440?

Mike it doesn't appear there's enough meat on the inlet of the waterbox to clamp the bpipe coupler to?

20x52x15mm bearings part# 6304-2RS ( check ebay is easiest..or ultimateindustrialsolutions.com ) where i purchased all my stuff 20x52x7mm seals i perfer one double lip and one single lip but either of each will suffice