Lucaumpits
RIDE LIKE U'VE STOLE IT!!
- Location
- Orlando, FL
you might have your breather tubes not installed right
Custom/Hybrid SUPERFREAK talk
- Thread starter JetManiac
- Start date
Lucaumpits
RIDE LIKE U'VE STOLE IT!!
- Location
- Orlando, FL
you r excused lol
- Location
- Grand Rapids, MI
I ground off the majority of the "tooth" to get mine to go on nice. I used a flat file instead of dremel.
My hooks are in almost the exact same location as Matt's.
Buckwild12
I'm moved by DASA power!
- Location
- Chester, Maryland
I'll jockey around with it a bit this week, I broke my turn nozzle ( it exploded to be more precise) it is an x-scream set up. My steering cable bent on the cooling outlet from my pump also. Ed has enough room with his pump to be able to mount the steering cable on the top part of the nozzle, I don't think with the cooling hose outlet on my mag pump that I can do the same, anyone have pics of their setup with a similar trim system. I had mine spaced about 3 inches low on the nozzle mount but it evidently it wasn't enough. Although the entire thing may stem back to when I tail darted the ski at VA beach when I wrecked my ankle.
- Location
- Grand Rapids, MI
I actually rotated my stator section of the pump 180 degrees to give the cable clearance on the cooling boss.
Buckwild12
I'm moved by DASA power!
- Location
- Chester, Maryland
Can't on mine I don't think, skat did all the work on mine and fused the 2 if it's not fused it sure looks like it there is no gap in the 2 sections that I can discern.
Buckwild12
I'm moved by DASA power!
- Location
- Chester, Maryland
I have changed around the hood side hooks so I get a better seal in the front portion but I still don't feel that it's sealing right/ well enough for my liking,other than that I am thrilled with the ski, it seems luxurious compared to my cramped little RN, no way am I ever going back 
the RRP riser bars are for sure the ticket for me and my gimp arm my back feels great unlike after wavedaze!
the RRP riser bars are for sure the ticket for me and my gimp arm my back feels great unlike after wavedaze!
That is what I was considering...
Brian, it is 2 piece(just machined from 1 piece of SS, then cut so the joint is hard to see) and you should be able to flip around
- Location
- Maryland
What is the least amount of motor to flatwater flip a carbon freak with moderate rider skill.
- Location
- St.catharines, Ontario
This is me with a 763cc ported big bore plus some goodies:
My technique sucks.
nice! did you complete it?
- Location
- SAN JOSE, CA.
How wide are the trays on these bad boys..... A few of my buddys ride the WDK Roks, do they come close to the wideness of the roks....??? Any info would be great !
Nosed in and rode out of it. I've seen my buddy do better on it.
It's my own lacking technique, otherwise they'd be plate to plate.
The individual pieces to a flatwater backie aren't that hard, but there are a lot of them to put together in a fraction of a second.
- get the setup wake right
- return at the right moment
- go slow
- squat low
- stand up
- arch back
- throw your head back
As you can see from the photo, I got the first four right, but didn't really stretch out, arch back, or throw my head back.
It's my own lacking technique, otherwise they'd be plate to plate.
The individual pieces to a flatwater backie aren't that hard, but there are a lot of them to put together in a fraction of a second.
- get the setup wake right
- return at the right moment
- go slow
- squat low
- stand up
- arch back
- throw your head back
As you can see from the photo, I got the first four right, but didn't really stretch out, arch back, or throw my head back.
Just as wide as an SXR if not more. I measured it at one point, I'm sure it's in my build thread. I want to say at the widest (inside the holds), it's 22 or 23 inches.