Search results

I have a Rzr 900 trail and a toy hauler. It is 21ft so doesn't have a separate garage. Anyone know of any mats that are affordable about 5'x9' that would work? Something like the liners that go in the back of SUV that have a little lip on them would be ideal as any thing that drips would get...

Yes. The starter has 2 lines. High and low. The low amp of the start/stop triggers the solenoid and lets the high amps go to the starter. If you jump the switch at the plug, and it works, then the problem is the start / stop or the connection. Using dielectric grease on the plug helps keep the...

The box corrodes to the studs. Remove the dash at the front of the tray. You can then removed the 4 bolts that are holding the 2 brackets in place. Once you have the ebox out with the brackets on it, let it soak with some penetrating oil. Heat may be necessary. Remove the bracket from the ebox...

Use a contour gauge, scan it into fusion 360 and 3D print custom tooling. It works very well.

There are a lot of products you can use and PVA is probably not the best one. PVA would be ideal if you are going to add additional material to it. Say for instance you are going to poly resin or gel coat and then paint. You would want that slightly uncured surface for your next coat, as you...

https://www.homedepot.com/p/RYOBI-ONE-18V-Lithium-Ion-Cordless-High-Pressure-Inflator-with-Digital-Gauge-Tool-Only-P737D/307627867 I use a lot of Ryobi stuff. Their big sell is that have the most tools. I have quite a number of them. Most work good, a few great, a few I would not recommend...

I'm not saying I will front the money, but A cylinder with powervalves that doesn't require case modification, a bolt on cylinder, is what I would be interested in. I have ridden stock motors with porting and I do not like them. I am very pleased with my stock cylinder porting that is very...

Teach me to weld!

I shortened my pole but didn't want to wait on adhesive to cure so I threw in some rivets and went to the lake. All was well and good until I did a sub. I went over the front and the pole came with me.

Two people beat me to saying "myself". My buddy lost the screw on top of his spark plug on his XL700. He temporary fixed it on the water by wrapping the thread in the foil from his pack of cigarettes. It worked well. My first trip to daytona was with the X2 in my avatar and I kept getting...

I see that now but only when searching a specific item. Is there a way to make that filter present at all times including when I am "browse all" without a specific search item typed in?

Go to the thread I mentioned abs read it. I think you are allowed to rack them up there.

https://thechive.com/wp-content/uploads/2021/10/92u9tekkphr71.jpg?attachment_cache_bust=3834235&quality=85&strip=info&w=400

Is there a way to block all items that need to be shipped. Too many items that are not local showing up in my market place feed.

Yes, you need to have 5 posts to send a PM to reduce bot spam. There is a thread about it stickied in the site info sub forum near the bottom of the list.

You have the motor out and shim the pump so that the shaft is in the center of the hole. Then put the midshaft bearing in. Then put in the motor and shim the motor until the 2 couplers are flat to each other. The boat is 30 years old. It probably has had the motor out and it probably wasn't...

I am pretty sure molded is a single piece of turf, where as cut is 2-pieces of turf with the top piece cut away. I believe single colors are molded and 2 colors is cut. That would make your picture a molded diamond. Whereas, a piece of black with blue marble would be black glued to blue marble...

I have only had a few motors rebuilt. I have used SBT cranks without issues. My skis tend to be rode fairly hard but stay lower hours. My Superjet motor for example only has about 60 hours in about 5 years but it has had salt water ingestion and it has been held WOT a lot of those hours on a...

https://www.harborfreight.com/8-piece-right-angle-screwdriver-92630.html I don't use the included bits though. I use a different set of bits. Flat 1/4" for the main jet and 5/32 for the pilot jet. I also use the Jetmaniac allen head screws so I use a #4 hex bit. The driver makes it easy to...

You don't have to remove the stock plastic to install a bilge switch, though it is easier. You don't have to turf the front if you remove the plastic. Primer is better than Choke. Worth the change. Having a primer pump inside the hull or priming manually sounds like a good idea, but mounting...