Search results

The parts fiche only shows the bracket for the two piece 61x manifold. Not all Krazes had the westcoast intake.

I checked a few websites and could only find the bracket for the regular 61x intake manifold.

Hi everyone! I'm curious if anyone knows of a different throttle cable bracket for a 61x setup. I have a wetjet carb and intake which both have the wide bolt pattern. The factory 61x bracket fits the wider bolt pattern now because I did a little grinding. The bracket is a lot narrower so I'm...

Well I'll be changing the main jet from 157.5 to 160. This thing is thirsty! I wasn't able to GPS the Blaster because it was obvious I needed to richen the main jet because as I was out 3 turns and she still wanted more! I might order a 162.5 just in case. I was able to GPS my WaveJammer...

I'll finally get to put the Blaster in the water tomorrow. I'll let you know how it goes and have some solid before and after data for comparison. Last season I was able to top out at 40mph so hopefully I can get 45mph out of it. No matter what I know the acceleration is amazing! The Blaster...

I picked up one of those tiny tachometers to help get my ski dialed in. I'm going to use the GPS speedometer on my phone to do some before and after comparisons. I know it feels faster in all ways but I want a little more data than what the old butt dyno can provide. Last season I GPSed it...

I'll finally get to test the Blaster on Sunday! I double checked the Blaster while running it in the hose and it seems to be running good. I also lowered the popoff on the Jammer so its throttle response is much better too. While I was in there I replaced and cleaned up the hoses.

I'm using the 2.0 needle and seat. I'll let you know how this jetting combo works out. It was really pulling hard last time I rode. My ski was fun before but now it is a completely different animal. I was riding at Klondike.

I fixed the fuel pump leak today. The paper gasket had a little tear and was causing the leak. I'll have to get it back on the water to verify my jetting. I'm at 130 for the pilot at 1 1/4 turn. It idles very smooth and has amazing throttle response. I could probably turn back the screw to...

Your ski looks brand new! Nice find!

Mine is a power spray without the spray. It is not crazy loud but it certainly throaty. It sounds pretty awesome! You will like it a lot!

I finally got my Blaster on the water! I have been out with an injury and have waiting months to try this thing out! The last time I rode, it was completely stock. I was able to collect a good list of parts at a good price, with the help of several members on here (Thanks guys!). My goal was...

I pulled the carb off again and found a few little pieces of debris and the internal filter was warped a little. I found the base of the carb was not square either. I trued the base by using a piece of glass and fine grit sandpaper. After my simple machine job it was perfectly square. I...

I cleaned and rebuilt the carb prior to starting it yesterday. I changed all of the gaskets and diaphragms. I'll go through it again to be sure. Do you think the 2.0 needle and seat at 19-20 psi popoff is right with that oceanpro vortex flame arrestor?

I forgot to mention my altitude is a little over 4000'.

Here's a picture of the new manifold and girdle kit.

I finally got all of my new stuff installed today! Here's the list of mods: Wetjet 46mm SBN carburetor Wetjet reed stuffer manifold Boysean two stage reeds Oceanpro Vortex flame arrestor Primer/choke plate eliminated Protec half girdle Wetjet/Westcoast with 30cc domes (180psi)...

Thanks for the heads up! If it's minimal I might just use washers. If not bolts are cheap!

Unfortunately I haven't thrown it together yet. These intakes are one piece so the reed cages bolt straight to the intake eliminating the separate piece between the intake and the case. I'll be sure to let you know how it performs once I get it on the water!

Hi, I just bought a Skat-trak 12-17 big hub prop and am in need of the rubber impellor seal and prop tool. I have the shaft tool but do not have the one to take the skat prop off. Thanks in advance!