Search results

Not confused

Going from 6 to 12 vien is a great improvement, the 400$ solas's are a great bang for the buck mod, not sure what the optimal set back is but I put one in my 95 and its awesome!

A good starting point for your pump and somone correct me if I'm wrong, this is what I've found to best for my boat, channel cut 201 intake, un molested 9/15 hooker with no spacer which I think gives you 3mil setback, solas mag stator, standard cone, nozzle bore(taperbore)at 85mm. I've played...

Don't forget that pump and prop tuning are just as important as all this motor work your gonna do

Upgrading from stock 38's to stock 44's won't yeild much improvement, well set-up 38's aren't bad but if your wanting to upgrade find a set of nice AM carbs(blackjacks, novi, fullspec). Sounds like your dropping some coin in that motor so might as well feed it properly. It's always finding the...

I've always re-used my stock gasket, if its ripped its toast, put some grease on it when re assemble the box, that really helps seal it up or silicone it closed. The thing with silicone is it makes it hard if you need to get back in the box but not impossible, silicone is best grease is second

Have never worried about water box, stock or aftermarket, I seem to never have fogging oil but always plenty of premix and wd40 is harsh but is a great degreaser and rust inhibitor. Wd= water displacement

I've always just got water out by starting it, a little premix down cylinders, drain gas and soaked her down with wd40. Same garage temps as you(I'm in fortcollins), no issues, I do make hot coco for it on the really cold days not sure if that helps or not

Get yourself a wetjet intake if your gonna stay with a single carb set-up

Those new coils are nice, I got one too, excellent product

Do you still have the heat sensor hooked up? I had similar issue years back, sounded like it bouncing off rev limiter at half crack, found where I had cut rev limiter out the wires were arking and making it cut out, year before that happend my heat sensor had gone bad and caused same issue

Lived in FW for a few years, great jetski and moto scene around there, lewisville was a great spot, my buddy lived on the lake in little elm so we'd rip across the lake to the marina bar for a beer and back, always loaded with good scenery at that place, grapevine was fun to, on the west end you...

Last year got a 01 zxi1100 for my wife with 35hrs on it, almost new condition, original owner, with trailer 1400$, they said it had an electrical issues, cleand wiring harness and one fuse later she fired up, around here that boat is worth 3000$

Correct, my bad for some reason I got off on a dry pipe tangent, limit your dents! And don't trust every thing you read!! There always idiots like me who are still hung over from New Years

(Edit ignore my ramblings)Grind your hull first and then smack that sucker, the outer size of that pipe is mainly all water jacket, it's rare to see a bpipe not dented to fit, usually means its not lined up properly, i think its more important that you also dent(only if needed but most do) the...

There is 2 forsale in Fort Collins, long drive but nice skis, both are 95 701's one is 2300 the other is 3000, check out fortcollins craigs list

There is actually 2 gangsters in Fort Collins

Street cred? Gangsters don't ride skis any way so they wouldn't care, flat water flips are cool but if want to impress your buddies flip a SN off a 15ft face, inverted 30ft above the water never gets old

Is still owe you a tank of gas! Took his 14 out in our buoy corse and didn't want to bring it back, the newer hulls I thought were amazing thru out, yes they chime a bit on glass if your not ready for it but took me 2 laps to get that to go away and I suck, simple intake and plate i think would...

what ride plate did you have before?