Search results

All valid points swap meet. Most of those reasons are why I have just been enjoying the set up myself the past few years. I didn't build it with any big plans in mind, just get my butt back on my ski more often. It works so well i thought I would like to hear what others like me thought of it...

No sit downs Wet dream. Your right they are very heavy and much wider also. They would not fit inbetween any seat config on a flat deck boat. Wish they would as there are a bunch more potential customers that way..:) Sent from my iPhone using Tapatalk

Ya McDog, I diddnt want to tip my hat to the design here. The pic is vague for that reason. I can tell you it stores great, it's super easy to use and I can load and unload the ski by myself onto the beach or in 10' of water. It's all aluminum construction and is less than 100 lbs complete. I...

My system will only work on a flat deck boat. A pontoon would also work for the system but the extra weight limits passenger capacity some. My tritoon is also a wide beam model. This helps for walking space around the ski in the front of the boat while its on deck. Sent from my iPhone using...

I designed and built a rack system to load and launch my ski from my Tritoon. I have had a 550, FX1 and now my carbon Rock on this setup. I have launched my ski at least 100 times over the past 5 years with no problems what so ever. My question to all of you is do you think it would be worth...

Whoops! Has to be more painfull some how..... When you get your new one finally this is how I painted mine up with ultra gray....,gota try something

One of the tricks I loved to do the most on my 550 as I diddn't have enuff power to do much else! Great advice here, body forward, foot to the low side in the tray, and really concentrate on your foot in the water an what it can do for you. Smooth water I could lean it over far enuff to drag the...

They have a bad rep for dying after moisture penetrates the alum housing somehow. Like said above, it's a potted box made for a jetski n it can't take the moisture? Sucks as they are simple dip switch design that works well controlling the curve but don't last. I run these boxes in my race sleds...

Haha, not funny! I couldn't wait to smash that picky shoria with my truck! I have rode quite a bit this season with no trouble but it is too early for a true opinion.... Sent from my iPhone using Tapatalk

They told me to buy the 36 also xjcrawler. My motor is a 927 WDK at 16.5-1 with a ton of timing in it and the 24 starts n runs the TL all day. Time will tell I it lasts.... The shoria sure diddnt Sent from my iPhone using Tapatalk

I have the earthX model 24. It's lithium, super light, an needs no special charger. Two year warranty to boot. Sent from my iPhone using Tapatalk

Ok. I will keep chasing it richer until it comes in. May get lucky and make it three little pick ups in a row....:) Sent from my iPhone using Tapatalk

I assumed it would need to be. The prefilters choke or restrict air flow rite? If your good with them on, off should need more fuel I thought. Richened 1/8 turn on the lows twice n it still was off. You think it should want less fuel with them off? Sent from my iPhone using Tapatalk

Yes they do wax. Cool thing was the jet diddnt change. I thought for sure I would have had to make a few stops chasing it but didn't touch the screws at all. I tried to remove the pre-filters a week ago n lost the jet bad! Two trips in going richer n it still wasn't happy so not sure what it...

Tks jackmarcus. I live rite by the tittabawassee river and have been taking short 30 min rides there as it is so close n easy. I used to ride at Sanford lake quite a bit. We should hook up sometime. Where do you ride? Sent from my iPhone using Tapatalk

Since the vid above I have changed two things on the set up. I changed the pump nozzle back to the stock 82mm size. Since the power is now there I thought it needed more load on the motor. It was a small gain but I do feel it accelerates a bit faster now. Second was to remove the reed stuffers...

I brought this post back to life to let everyone who helped me know how it turned out. First of all I want to thank Jeff at WDK. He doesn't know me from Adam. All he knows is I bought one of his skis and needed help dialing it in. I really have followed most of his recommendations and am on it...

Carbide drill in the hands of a pro will get them out no prob. Do it of you can, if not send it. Sent from my iPhone using Tapatalk

Ya that guy was pretty excited about his 600 trail sled! Lol It really just confirms that you can't be certain either way that with or without stuffers is good or bad in every set up. If you buy the newest force 3 reeds you have options. I'm not sure about monkey's n foreskin but I want to be...

I'm gonna try it wax. I am very curious myself to the result. If I get more mid range and top end than I have now.....oh boy!! Sent from my iPhone using Tapatalk