Search results

Red coil wiring That Red coil was my favorite.. It produced better accelleration than the new Black ones, (IMO).. Black = Ground (outside of loom) The other black = CDI black Brown = cyl 1 Orange = cyl 2 Yellow = cyl 3 This is for a triple, so disregard the Orange or Yellow wire...

Shipping. USPS tracking sucks.. You have to personally ship international packages, as they aren't so lenient after 911, Most USPS employess are grumpy and they don't want to pick up packages at my shop.. They prefer I deliver them to the Post Office.. As a business, you are held to a lerger...

Snap-On I was joking about the Snap-on truck... But I wanted to get the message conveyed.. REMEMBER.. "Quality is Priceless". Thanks, Randy

I will ship anywhwere... BUT I only ship UPS or DHL, as it takes me over an hour to drive to the Post Ofiice & back..If you need a part from me, often the best solution is to send it to a friend of yours in the USA and have him re-send it to you. I apologize, but there just aren't enough hours...

Easy Project Matt, Run down to the Snap-on truck (LOL) and buy "Needle nose" vice grips.. Then grind one side of the vice grips into a point, so when you close the pliers on the throttle plate screw the pointy side splits the screw and mushrooms it.. (just like a log splitter at home on the...

Backfiring Split the cases and install new crank seals, that's why you had oil in the front cover.. Then replace the stator, as the "Pulser coil" is probably bad, causing the backfire.. JSS can test / repair the stator for you.. Be careful using cheap replacent stator coils, as they often don't...

Oils.. The harder you work the motor, the better oil you need.. It's all about film strength & migration time.. Just because your motor is oily when you take it apart doesn't mean your oil is working for you.. Look at the piston pin grooves, the wear in the pin area of the piston itself, the...

Spark Plugs It's difficult to make a 100% evaluation, but spark plugs loosening are generally caused by detonation in the mid range.. If you have the timing advanced 3mm with an OEM cdi, you might be on the edge already. This depends upon the impeller pitch, stinger diameter, etc.. If you have...

CDI's for sale. Keep your original CDI, and I will sell you a good used one for $60.00. I have about (10) of these, and I think a few are modded already.. wcc@watcon.com

Riva flat-tops. I have a set in stock for sale. I set them up at approx .016" - .020" ring-end gap. It's not the clearance, it's the break-in.. Randy wcc@watcon.com

Leak The usual culprit is a warped cylinder deck or cylinder head...If you cant find the leak anywhere else, get a thick piece of glass, tape some high quality sandpaper on it, spray with WD-40 and carefully make some "figure 8" passes while holding the cylinder / head directly against the...

Wiring I don't have a schematic to post, but if you don't figure it out give me a call at 360 692-3492 You are correct, as the inline fuse is for the main power in... Thanks, Randy

Complete pipes & Headpipes in stock.. I have new headpipes, exhaust manifolds, b-body pipes, SXR-Wet & Dry pipes, etc in stock.. The prices will be the same as on the Riva site,and I'm sorry I can't offer a discount as dealer pricing leaves no real margin.. Contact me direct at wcc@watcon.com...

Clup plug.net Thanks for the link.. Their price is cheaper than I pay for them.. Most plugs are available in the solid top by adding the "S" as previously mentioned.. If you want to see a cool salt water plug, look up the NGK BR8EQ. Thanks, Randy

BR8ES Solid tops. I have them for $2.25 each

Motorhead, please contact me at wcc@watcon.com Thanks, Randy

Jet sizes I carry a full selection of jets up to #160, and it's not unusual to use them in certain applications. http://www.watcon.com/Catalog_Pages/Carb_Jets.htm Contact me directly at wcc@watcon.com Thanks, Randy

Send me a e-mail directly to wcc@watcon.com and request my tuning tips for rookies. It might help you a bit and it's free. 650's generally require a pretty large low speed jet, and usually near 20 lbs pop off. Thanks, Randy

Bring your umbrella. I will be headed to the races on Saturday. I will be more than happy to offer free technical advice on jetting, etc if somebody is having a difficult time.look for me at the Crossens rig or the Kent Kawasaki truck.. Thanks, Randy

I will be leaving on a business trip May 28th, and returning June 4th.. If you have any pending orders that need to be shipped on Tuesday, please contact me ASAP. Sorry for any inconvenience! Regards, Randy