Search results

Looking for help in deciding what to purchase next for my RN. Currently have most of the standard bolt ons for my 701, B-Pipe, head, reeds etc. Hull has holds and good turf. I am looking into aftermarket hull options but am not yet ready to pull the trigger. Any further mods i make to my...

What's you carb setup? Single carb or Dual? External fuel pump? Etc. give us as many details as possible and we'll be able to help you better. Also post pics. *edited for repeated suggestion

almost certain that the pieces shown in post #1 are the same for both SN and RN. So i think yes. maybe someone else can confrim

^^^ yup tire tube pieces is what i used. one piece over the intake manifold under the carb bases, bolt the carbs down over the tire tube one piece over the b-pipe manifold, bolt the headpipe down over the tire tube. basically replace your carb base gasket and b-pipe gaskets with pieces of tire...

I installed an sbt cable on my RN recently and the white clip snapped in with some pressure, but nothing to make me think it would break. If u dont have a spare be careful. If u got a set of calipers, measure OD on cable notch and ID in clip to make sure they're not way off. Sent from my...

You have the parts in the proper order in the first pic. The rubber gland seal goes on tight but not crazy tight and should slip just past the notch in the cable. The plastic clip opens up and closes back into the notch. The metal washer buts up against the plastic clip. The threaded cap locks...

Cheap insurance to change out those crank seals, so that's what I would do. If you do decide to close it back up and ride, make sure to clean the whole area well then check for oil/residue after a short while. Failed front crank deals are harder to detect, but oil/residue behind the flywheel...

Epoxy over poly is ok but not the other way around. This is what ive been told. Sent from my iPhone using Tapatalk

Another vote for Deka ETX9. My RN has all the common bolt ons and it does the job perfectly. Buddy of mine with the same setup uses a ETX12 and loves it. Deka batts are made by East Penn i think and that company makes several private label batts such as "intimidator" which are identical to...

just made my payment. 3 clicks and 10 bucks to support the X

decided to go with a rebuild crank from jetmaniac

hey guys, i'm trying to get an idea of how difficult it is to replace the front and rear crankshaft bearings. The front crankshaft seal failed on a buddy's 701. while replacing it we noticed the black plastic race on the front bearing was cracked and we're not gonna reassemble as it is. (not...

I have a blowsion billet gas cap, which probably doesn't make a difference. When un screwing the cap i get the usual pressure release which is stronger after the ski sits in the sun for a while, all of which is normal. Sent from my iPhone using Tapatalk

Yes routed up the pole, basically stock installation for the vent tube. Is the height up the pole a real issue. Barely any water builds up in the decanter and i check it regularly. Sent from my iPhone using Tapatalk

Ive been following an issue over the past couple of months. I find that while riding water builds up in my fuel filter (oem filter). So there must be water in my tank. I notice the effect on my engines performance, i take it to shore right away and inspect the filter. I drain the filter...

as compromise for durability that stuff better feel like one of those dr scholls commercials found one... http://youtu.be/GVArj1V-jks

my 2yr old son got the addiction pretty bad too! he's gonna love one of these, thanks for the links.

Subscribed! Lol Expecting to see some wacky pics of hackjob marine audio setups!! Haha Joking asside, prob relatively easy to install small speakers on the pole or something. Where u mount a head unit though?? Sent from my iPhone using Tapatalk

Thanks for the replies Sent from my iPad using Tapatalk

Quick question: can the crankcase on a 61x/62t be split without removing the pistons from the rods? Sent from my iPhone using Tapatalk